Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

New Bench Vise *LINK*

Posts

New Bench Vise *LINK*

#1

New Bench Vise *LINK*

Paul in NJ

I have finally finished my kitchen make over and the shop is free of the new cabinets built in there. I am now spending time on projects on the exterior of my home. When we get a rainy day I have some time to mess around in the shop.

A while back, Steve Voigt (http://blackdogswoodshop.blogspot.com) had a blog post of a high vise he had built. I believe he was inspired by the Benchcrafted model (https://www.benchcrafted.com/hivise). The Benchcrafted hardware is very nice but Steve used some hardware he had on hand and modified it to his purposes. It was nice enough that I was inspired to build my own.

I found some cheap acme threaded rod and nuts on Ebay, ¾-5 for the main screw and ½-10 for the clamps. I had saved some cherry from the firewood stack. I didn’t complain to my firewood guy that the load he delivered wasn’t 100% oak. It sat under my bench for a few years waiting for the right project. The vise handle is a 3/8 bronze carriage bolt with the head cut off. The clamp handles are dogwood as is the hub. Brass waste plumbing pipe was used for the hub bands and scavenged brass hex stock for the clamp pads.



Steve’s vise used a parallel guide to regulate the jaw opening. The Benchcrafted version uses a sliding cross type of apparatus as the original did. The original also had a cheaper version that uses a second threaded rod at the bottom and a nut you spin to regulate the opening. This is the version I used. I have not installed a garter to pull the vise open when you back off the vise. I decided to live with it for a while before I do anything. The jaw is lined with cork from flooring tiles. This cork has proved durable glued onto my holdfasts pads. I added steel reinforcing plates to the back jaw. I was worried that there would be a lot of stress on the bottom arms since they only have a half lap joint. My firewood wasn’t long enough to make a dado joint there. The screw is epoxy bonded to the hub with thickened West System Marine epoxy and the hex nuts are mortised in with a little epoxy to hold them in place.

In use the vise is rock solid clamped to the bench and has tremendous grip. I will see if the missing garter and the adjustment nut are tiresome in use. I envision using it for chair spindles and detail work as well for spoon carving (I use a drawknife and spoke shaves).

Regards,

Paul Dzioba


Steve's Blog

Re: New Bench Vise *LINK*

#2

spoons

Bill Tindall, E.Tn.

I see spoons at craft fairs and I wonder, how did they do that. If anyone else is interested I would like a few pictures that show the process. I am especially bewildered by how perfect the inside and outside of the hemispherical part typically is. Any way I can imagine doing it would result in lumpiness.


Re: New Bench Vise *LINK*

#3

Re: New Bench Vise

John Jardin

Very nice

Re: New Bench Vise *LINK*

#4

Be carefull Bill ...

Raymond in Trenton NJ

Pretty soon Paul will have you making curved knives. Don't ask me how I know this.

Raymond

ps - As all your work is, very nice spoons Paul. You should show them your knife box and portable 'shaving pup' :o) I like your vice. Just what we all need, a small, portable leg vice.

Re: New Bench Vise *LINK*

#5

Re: spoons

Paul in NJ

Hi Bill,

I will post some pictures some time and talk about my process. My spoons have facets left over from the knives. My spoons are made to be used and all the surfaces are finished with edge tools. If they were sanded, they would fuzz up when they came into contact with liquids. Walnut oil is used for the finish.

regards,

Paul Dzioba

Re: New Bench Vise *LINK*

#6

Re: New Bench Vise

Steve Voigt

Nice job, Paul! So glad you found some inspiration from my version. The threaded rod adjuster at the bottom, like the parallel guide, is an old and venerable solution for the leg vise--nice to see it in action. Nice spoons, too. You've been busy this lockdown! :D

Re: New Bench Vise *LINK*

#7

Re: spoons

Oskar

Sorry Bill, I don´t have in progress pictures. But getting a smooth spoon bowl is not that hard with a hook knife. And the rest with a usual knife, often dubbed sloyd knife. Virtue is you dont need any workholding at all. Just carve with spoon in hand, and braced against your body. Drawknifes and gouges are also a alternative, often used with a so called spoon mule, a shave horse type for spoons and ladles.

Barnaby Carder, calls himself 'Barn the Spoon' has some videos showing great technique. Search for "silent carving" and "barn the spoon" on youtube.

Re: New Bench Vise *LINK*

#8

Re: New Bench Vise

AZ in Colorado Springs

On my leg vise I have the parallel guide, drilled with numerous holes for a pin. In practice, though, I have several shims which in combination if necessary set the bottom opening of the vise to about 1/4" wider than at the top. These various shims have a slot about 9/16" to slip over the 1/2" parallel guide. Your shorter vise would probably not need a 1/4" differential but the principle applies -- it's a lot less fussy than realigning the pin for different thickness of stock. And if I clamp up a drawer (exceeds my combined shim set), well I can use the pin.

Nice vise!