Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

(Roubo) pole lathe dimensions

Posts

(Roubo) pole lathe dimensions

#1

(Roubo) pole lathe dimensions

Steve Voigt

This is mostly a question for Warren, but anyone else, feel free to join in if you have experience with pole lathes. I'm wondering about some basic dimensions: the height of the centers being the most important, followed by the height of the bed, the height of the headstock upright, and the swing. Perhaps it's better to think in terms of these things relative to the user's chest or belt, but I think you (Warren) and I are of similar height as I remember.

I've been watching Peter Follansbee's recent videos, and I'll probably copy his basic design, which is a little simpler and requires less lumber and fewer joints than the Roubo.

I'm not quite ready to start making a lathe, but I've picked out some stock (some very thick beech that's unsuitable for planemaking) and would like to sort out some dimensions so I can start to break down the lumber. Thanks in advance!

Re: (Roubo) pole lathe dimensions

#2

justin ball

Re: (Roubo) pole lathe dimensions

justin ball

I built my first one from junk at the dawn of the interweb and was just sort of what I had and seemed right. I''m doing the same again, but with a better eye, but still found in the back lane stuff. You can always a make a 2.0, 2.5 etc.,. Do what works and be happy with the result. Shiny is overrated.

Re: (Roubo) pole lathe dimensions

#3

related question

Bill Tindall, E.Tn.

Is using a pole lathe ergonomically any different than using a motor powered lathe? (I used one at Old Salem and all I remember was it was too high for me. It did not stand out that my hands were in a "natural" position at any different height than on my lathe. Well, I do remember it was like chewing gum, rubbing your belly and hopping on one foot. )

If not, these questions can be answered by visiting the Turning Forum, or someone with a lathe. For me, on a motor powered lathe, the height of the centers is critical with some tolerance. I have used lathes where I stood on a platform to get higher and more relaxed.

The other questions are dependent variables fixed by the height of the centers and what swing you desire.

Re: (Roubo) pole lathe dimensions

#4

Re: (Roubo) pole lathe dimensions

Warren in Lancaster, PA

Here is Roubo's measured drawing:


It appears to me that the bed height is around 36 inches and the height of the centers is about 11 inches above the bed. My own lathe has 35 inches for bed height and 9 for center height. I don't know if I intentionally deviated from Roubo measurements in 1981. In any case, the height can be compensated for by changing the height of the tool rest, so it is not as critical as might be expected. Roubo shows one tool rest, but a turner may have had half a dozen at different heights.

Note that Roubo shows two positions for the cord: one going through the bed and one going on the far side of the bed. These are like two different gears, one has more speed and one more power. I use the cord through the bed, but Peter and many others today use the outside cord. In historic drawings you see both ways.

Note also that the centers are not in the centers of the puppets for this type of tool rest.

My lathe has 36 inches between centers, because I was unsure of the success. I would do 48 today. When I made the lathe the literature (Bealer, Dunbar, Nutting, Hummel) was very dismissive of the pole lathe and described it as clumsy, crude, inefficient, and stupid. None of the writers actually knew how to use a pole lathe.

Re: (Roubo) pole lathe dimensions

#5

Re: (Roubo) pole lathe dimensions

Warren in Lancaster, PA

Here is a finial I made in 1981 the month I was learning to use the pole lathe. At that time I had two gouges and a homemade skew. This was waxed once and has no other finish. Can you tell that it was not sanded?


Re: (Roubo) pole lathe dimensions

#6

Re: related question

William Duffield

Ergonomically, the pole lathe is different, since you have to be able to stabilize the tool on the tool rest while operating the treadle with your foot. In addition to keeping your upper body stable, you are using more energy with your leg. Using shorter, interrupted cuts also helps to stabilize the upper body. You don't keep the bevel rubbing. Instead, you typically plunge the tool while pushing down on the treadle, and back off in preparation for your next cut while the pole is returning the object. Note that I have tried using a pole lathe, but am not proficient. Trust what Warren teaches you, not what I say.

If your centers are too high, you have to lower the tool rest; if the centers are too low, you have to raise the tool rest. In the former case, your tool is cutting more towards the front of the work. In the latter, more towards the top. I usually adjust the tool rest so with a long tool handle, the handle is resting on top of my hip bone; with a shorter handle, my ulna or wrist is resting on the ho=ip bone.

There are operations you can do on a pole lathe that you can't do on a treadle lathe or powered lathe, taking advantage of the partial rotation and interrupted cut of the pole lathe. Good examples are turning a mug with a handle, a pitcher, or a bowl with two handles. I found these on Reddit, but my Ah! Moment was watching Jarrod Stone-Dahl demonstrate the process.


For the pole, choose a hickory sapling.

Re: (Roubo) pole lathe dimensions

#7

Re: (Roubo) pole lathe dimensions

Don Stephan

Somewhere saw a video of an English chap using a spring pole lathe with a hook tool, seemed much more efficient than a "regular" gouge.

Re: (Roubo) pole lathe dimensions

#8

question remains

Bill Tindall, E.Tn.

That was a lot of information but none addressed the question posed. Would someone that found the ideal height of centers for a motor powered lathe desire a different height for a pole lathe? It is not an irrelevant question for someone about to invest a bunch of time building one. It would not be hard to find a motor driven lathe and determine the ideal height of centers at it, then replicate if the replication if the two are similar. The centers of my lathe are 42" and that is a comfortable height for my hands/arms and tool presentation while turning. I could live with 40. I would want to stand on a stool at 48". But perhaps tool presentation is different for a pole lathe or others like to hold their hands higher.

Re: (Roubo) pole lathe dimensions

#9

Re: (Roubo) pole lathe dimensions

Wiley Horne

Hi Warren and all,

That is a fabulous drawing in Roubo! Different views in the same plane.

Warren can you comment on one thing. And this may be a dumb question, because I’ve never seen a pole lathe.

It looks like a critical dimension is the diameter of the work piece where the rope wraps around it. My thinking is that diameter sets the rotational speed of the lathe. For example if one treadle throw is about 19”, and if the diameter where the rope wraps around is 1”, then 1 treadle stroke will cause the work piece to turn about 6 times. But if the diameter is 1.5”, the workpiece will turn 4 times to one treadle stroke.

I’m slowly getting to my question: Is there an ideal or typical diameter where the rope wraps around? And how do you arrange for this section to be turned onto the workpiece, before getting to the design itself?

That’s a wonderful finial! Thanks for showing.

Wiley

Re: (Roubo) pole lathe dimensions

#10

Re: (Roubo) pole lathe dimensions

Warren in Lancaster, PA

I usually use a block knife to rough out a spindle, but probably the most common tool is a hatchet and a block, which are seen in old drawings of turning shops. So once you have a rough blank you make a small impression in each end and wrap the cord around the blank.

The first thing is to turn a pulley at one end, a smooth shallow cove for the cord. As soon as the pulley is done the piece is turned around so the cord rides in the pulley. As you have suggested, Wiley, the smaller the pulley the more revolutions, but the trade off is power. So we can turn with pulleys of various diameters but maybe an inch or so is a good compromise between revolutions and power. The power is very important not only to take a bigger chip, but to have the steadiness to make a smooth cut. In may cases we a pulley at each end for the bulk of the turning, then cut them away at the end, with the cord on any convienient place.

Re: (Roubo) pole lathe dimensions

#11

Re:  question remains

Warren in Lancaster, PA

My pole lathe centers are around 43. On an electric lathe some turners hold their hands quite close together on the tool. I think for the pole lathe it is helpful to have somewhat longer tool handles and spread the hands out, maybe a foot or more apart. This gives more leverage and control. The right hand can be held quite low.

So there could be differences in tool presentation, or it could be that the lathe at Old Salem was just not that well set up.

Re: (Roubo) pole lathe dimensions

#12

Re: (Roubo) pole lathe dimensions

Steve Voigt

Warren, thanks much for the illustration and for your measurements. It's very helpful to have a starting point based on concrete, practical experience. Not sure when I'll get around to this, but I'm sure I'll have more questions then. Oh, and on the length--4 feet sounds good to me. My timbers are around 5', so I'll be lucky to get 4' between centers.

Re: (Roubo) pole lathe dimensions

#13

Thank you!  Great clarity.


Re: (Roubo) pole lathe dimensions

#14

Re: (Roubo) pole lathe dimensions

Warren in Lancaster, PA

I skimmed over Roubo's text last night. He mentions bed height as 36 to 39 inches, puppet height as 12 to 14 inches (height of centers would be slightly lower), bed gap 2 inches, pole 8 feet (2 to 2 1/2 diameter), lathe length 5 to 6 feet. I use a 13 foot pole of roughly the same diameter, which I would recommend.

The illustration is one of those that Roubo engraved himself.

Re: (Roubo) pole lathe dimensions

#15

Re: Thanks Warren!