Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

kiln temperature

Posts

kiln temperature

#1

Jack Guzman from Maine

kiln temperature

Jack Guzman from Maine

l use a small kiln to dry windsor chair parts. It is 2'x2'x3' with an inlet hole low down and an opposite outlet hole up high to encourage air flow through the kiln. I use three 150 watt incandescent bulbs for heat. I have a temp sensor/regulator to control the temp. I keep it between 125 deg. and 140 deg. My temp control unit stopped functioning so the temp rises unchecked. It tops out about 170 deg. I just unscrewed one bulb to drop the temp down to about 140 deg. I need a new controller.

Anyhow,there is a question here. What temp should I keep the kiln at to properly dry chair parts completely? I dry oak spindles ,chair leg tenons(they enter the kiln through holes in the top) and various bent chair parts. I guess that 170 is too hot? Stuff should dry quicker but I'm worried that too much heat can be harmful somehow. Does anyone know enough about this to help me?I usually start with green wood.

Re: kiln temperature

#2

Clint Searl

Re: kiln temperature

Clint Searl

Rather than trying to come up with some theoretical "perfect" schedule, if what you've ben doing is working well, just stick with it.

Re: kiln temperature

#3

Jack Guzman from Maine

Re: kiln temperature

Jack Guzman from Maine

Actually,before the temp control failed I had no idea I could get it so hot in there . Thinking it may be useful is what prompted my question.

Re: kiln temperature

#4

VA Tech data

Bill Tindall, E.Tn.

I checked some drying schedules published by Virginia Tech. The control variable in a commercial kiln is humidity in the kiln. The kiln variables of air velocity and temperature are controlled to control the drying rate which is determined by the humidity in the kiln. For oak, a notoriously difficult wood to dry, the starting temperature is often 100 F and the final 170 to 180. The final temperature is what it is to get the wood below 7% MC. The starting temperature for poplar would be higher.

Re: kiln temperature

#5

Re: VA Tech data

Larry Barrett

Bill, is the VT data publicly available, and if so, do you have a link to it?

I dry chair rungs in my kiln, and set the temp to around 140 F. I determine when 'done' by weight - keep in the kiln until no more weight loss. This usually takes a couple of days for a chairs worth of rungs. I have continued drying at a higher temp as a test, but can not detect any appreciable difference in weight, maybe a gram or two after an extra day.

Re: kiln temperature

#6

Re: VA Tech data

Bill Tindall, E.Tn.

Any of the kiln manufacturers will have similar data. What I quoted is Drying Management Notes number 16. VaTech Forest Products department. I live in the world of hard copy publications.

Re: kiln temperature

#7

Jack Guzman from Maine

Re: VA Tech data useful

Jack Guzman from Maine

That helps. I guess 160 should be safe enough. I dry mostly red oak. It is what I use for steam bending and all spindles I make are oak.

Re: kiln temperature

#8

Re: VA Tech data useful

Bill Tindall, E.Tn.

If not cracked you didn't get it too hot too fast. The risk with oak is too fast drying what ever the temperature. Much checking of oak begins as high as 40% MC according to literature.

Re: kiln temperature

#9

Jack Guzman from Maine

Re: VA Tech data useful

Jack Guzman from Maine

I was taught to air dry parts for a week or so before placing in the kiln. Most of the time I follow that rule. Early on I placed some freshly turned green maple leg blanks in the kiln,they checked badly. So now I don't try to rush things. I make the blanks round then air dry them before turning into legs,then kiln.

Re: kiln temperature

#10

Re: VA Tech data useful

Bill Tindall, E.Tn.

Unlike a board you get a near equivalent drying from two sides. Much faster. Drying lumber is all about not creating steep moisture gradients in the wood while getting it to useable dryness as quick as possible.

Re: kiln temperature

#11

Re: VA Tech data useful

Larry Barrett

I make post and rung chairs, starting with a log. Oak, mainly. The rungs are rived from the log, drawknifed to octagons, approx 3/4" diameter. By the time they are ready for the kiln, they are probably around 20% MC, maybe a little higher. I run the kiln at 125-140 F and have never had any checking problems. Maybe lucky based on what you are reporting, but also maybe because of the fairly small cross-section area.

Re: kiln temperature

#12

Re: VA Tech data useful

Philip F Duffy

The School of Dendrology at VT is a great source of data about such matters, and many others. It is noted to be one of the finest schools of its kind in the nation. They are on-line and just go to Va Tech web page. P.