Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

moulding plane reconditioning

Posts

moulding plane reconditioning

#1

moulding plane reconditioning

john lucas

I have been buying and reconditioning old molding planes. I do mostly turning related furniture repair but in the last 10 years have been doing more and more flatwood furniture repair which is why I'm picking up these planes. On the curved blades it pretty obvious the blade should match the body profile but on this one the blade is wider than the body by .030". Should I grind it down. It's an odd size. cuts a groove that is .700" wide right now. I'm mostly using it to clean glue off of tenons right now but could easily see a need to use it to clean up a groove. I'm tempted to thickness the whole plane to .625 and make the blade match. What are your thoughts.


Re: moulding plane reconditioning

#2

Re: moulding plane reconditioning

david weaver

That's quite a bit of extra width for the body, which makes me wonder if that's all just shrinkage, or if it's a non-original iron.

The large mouth may cause you some issues, especially on smaller work, but you can patch that if needed.

As far as the iron size goes, you want the iron to be slightly wider than the plane body. How much is the guess - "a little" is what I'd say, like perhaps half or a third of what you're showing.

You want to be able to manipulate its use so that you can have it flush with the side of the plane or more often just slightly proud (to prevent a square cut from creeping toward the edge of the work piece, which is what will happen if the body and iron are identical in width).

I'll defer to anyone who has ever measured for an exact number, I've only used kentucky windage.

If you grind the iron back a little bit, make sure the edges have some relief so that they scrape the side of a cut and don't act to push the iron away from the cut itself.

Re: moulding plane reconditioning

#3

Re: moulding plane reconditioning

Oskar

is the wedge a good fit? might have gotten the wrong/not original iron at some point?

If the iron mortise allows for setting the iron flush with the right side you could use it as it is, after making sure the sole is flat, and th reference sida as well. That is, as a skew rabbet plane. As for making grooves I don´tknow how well it works

Re: moulding plane reconditioning

#4

Re: moulding plane reconditioning

Wiley Horne

It’s a skew rebate. To function as a rebate, the blade at the edge has to be a few thousandths wider than the body. Particularly on the cutting side. If the blade is not a little proud of the body, when you plane a rebate, the plane will progressively walk away from the sidewall with every pass. Also, when the blade is a little wider, it gives you some flexibility to deal with the situation where the blade is not sharpened dead flat with the plane sole—you can make small adjustments to make the plane cut properly, even if the latest sharpening has the blade slightly higher on one side.

For example, on my LN large shoulder plane, the blade is exactly 0.004” wider than the body. I wouldn’t mind if it were a coupla three thousandths more than that.

Suggestion: make changes slowly. Test the plane as a rebate plane; hammer tapping the blade into position on the cutting side as you go; Be guided by the results. Also, do whatever Warren suggests :) .

Wiley

Re: moulding plane reconditioning

#5

Re: moulding plane reconditioning

Warren in Lancaster, PA

This is a skew rabbet plane. We don't use rabbet planes for making grooves. We use them for making rabbets, adjusting rabbets, and making fillets in mouldings. You can use it for trimming a tenon, but I would be leery about using it to clean off glue because the glue would be hard on the plane sole.

This type of rabbet plane is used for deepening rabbets where the right side of the plane rubs against the shoulder of the rabbet. (A square mouth rabbet can be used left handed also, where the left side rubs against the stock, but a skew rabbet cannot.) The iron is from a different plane. On the right side of the plane, looking from the top, the iron has to protrude a small amount for clearance. You want it so that a straight edge held against the side of the plane will rock a little on the edge of the iron. The plane will work the way it is but better if the iron doesn't protrude quite so much.

On the left side of the plane, the iron does not have to match up at all. It can be short of the edge of the beech, or long the way it stands now.

Re: moulding plane reconditioning

#6

thanks for all the great info

john lucas

That's exactly what I needed to know. I'm guessing this iron came from another plane also but that's what you get when you pay $5.

Re: moulding plane reconditioning

#7

Good value at $5

Jim Matthews

Clean irons alone are worth that sort of money.

Unmentioned above is sharpening the SIDE edge of the iron facing the work.

I was taught to lap this additional cutting edge at less than 90 degrees.

****

In practice only the first few thousandths contact stock, but it's easier to polish the entire face.