Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Cleaning up the inside of a gouge blade

Posts

Cleaning up the inside of a gouge blade

#1

Cleaning up the inside of a gouge blade

Jeremy Osner


I've managed to get this gouge just about sharp using a few different slipstones on the inside of the blade. But the "flatness" of the back is only for a couple of millimeters above the sharp edge. What would be the best way to clean up the rust beyond where it's sharpened? The blade is curved in two directions so no stone will really work. Except maybe the end corner of a rounded slipstone?

Re: Cleaning up the inside of a gouge blade

#2

Re: Cleaning up the inside of a gouge blade

Jeremy Osner

Or maybe better said, the back is not "flat" at all, it's the microbevel that gives it a sharp edge. I think I should try using the corner of a slipstone and get the back closer to even.

Re: Cleaning up the inside of a gouge blade

#3

Re: Cleaning up the inside of a gouge blade

Jeremy Osner


answered my own question -- sandpaper to clean up and slipstones to sharpen.

Re: Cleaning up the inside of a gouge blade

#4

Re: Cleaning up the inside of a gouge blade

Bill Houghton, Sebastopol, CA

If I recall correctly, putting a microbevel on the inside of a gouge is one kind of standard practice in sharpening.

As to the cleanup that you later figured out how to do, coarse steel wool lubricated with mineral spirits could work, too. Use a good big hunk, and your fingers can avoid the sharp edge.

Re: Cleaning up the inside of a gouge blade

#5

Re: Cleaning up the inside of a gouge blade

Hank Knight

I would follow Bill's suggestion with a Dremel and a small buff with Autosol.

Re: Cleaning up the inside of a gouge blade

#6

Re: Cleaning up the inside of a gouge blade

Jeremy Osner

nice -- will steel wool + vinegar also be a good treatment for a rusty steel square?

Re: Cleaning up the inside of a gouge blade

#7

Sure, why not?

Bill Houghton, Sebastopol, CA

Vinegar is a mild acid that is, in household concentrations anyway, too mild to cut the steel itself very fast. I find, when I soak tools in it, that they wind up a dark color, but I can usually polish that out fairly quickly.

Re: Cleaning up the inside of a gouge blade

#8

Re: Vinegar + rust

Jeremy Osner

I got out vinegar and steel wool and took a pass at a couple of gouges and squares...


I believe it will take another pass for it to actually be rust-free but it looks much better than it did before.

Then I realized I have several unused rusty scrapers, so those came out to soak in vinegar. They have mostly cleaned up nicely too.

I had (too late) the thought that I should save the slurry of rust and vinegar, to use as pigment -- is there anything to that? Seems like it would dry out pretty quickly to a very nice shade of red.

Is there anything I should do to dry the steel off afterwards besides a paper towel?

Re: Cleaning up the inside of a gouge blade

#9

Re: Mineral spirits + rust

Jeremy Osner

Huh, I went back and read your original comment, Bill, and see you were talking about mineral spirits -- somehow I had in mind that you recommended vinegar. My second pass will be with mineral spirits, that should be more effective and also will dry without rusting.

Re: Cleaning up the inside of a gouge blade

#10

Re: Vinegar + rust

Bill Houghton, Sebastopol, CA

Some people mix up baking soda and water to neutralize the vinegar. I'm planning to try that when next I do some clean up. What I've done in the past is rinse the vinegar off with copious amounts of water, pat the tool (or tool parts) dry, then spray the tool or parts with plenty of WD-40 to neutralize the remaining water.

Even with baking soda, I think I'll follow the water rinse/WD-40 soak practice.

Re: Cleaning up the inside of a gouge blade

#11

Re: Looking cleaner

Jeremy Osner

I went over the tools once with mineral spirits and they are looking cleaner. The ruler for instance was still pretty illegible after the vinegar, it's looking like a ruler again.

there are still spots of brown on the handle of the small square, I think that is rust. I will try scrubbing at it some more...

Re: Cleaning up the inside of a gouge blade

#12

baking soda unnecesssary.

Bill Tindall, E.Tn.

Acetic acid boils near the BP of water. When the water evaporates the acetic acid will evaporate along with it. That said, this kind of cleaning can leave a high surface area which will oxidize quickly. So prompt drying and oiling or waxing could be necessary.