Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Triangular dovetailed box, marking added

Posts

Triangular dovetailed box, marking added

#1

Triangular dovetailed box, marking added

Bill Tindall, E.Tn.


On the off chance that someone might need a triangular box the details of laying out the dovetails are described. This one and its mate will flank the drawer in the corner cupboard as secret compartments that will, in place, look like drawer guides.

To me, and wife that helps glue complex assemblies, there is something not intuitive about the dovetails. When learning I made a box of scrap dovetails with every possible orientation of the tail and pin angles wrong in some way or another. Even when assembling we wanted to put parts together backwards. I now label all intersecting pieces to avoid confusion when assembling.

You must become a pins first advocate no matter your upbringing.

In a square box the base lines are off set from the ends by the thickness of the stock. In an angled box the base line is off-set from the tip of the long side by the width of the bevel(1.4 times the stock thickness for a 45 degree box). And for the short side the base line is off set the stock thickness plus the width of the bevel from the tip. For example on a 45 degree box made from 1" thick boards the base lines are 1.4 and 2.4 inches from the long side. I set a marking gauge for each distance to scribe these baselines

Marking the tails from the pins involves holding these parts in registration with the long side of the pin board aligned with the short side of the tail board. If someone figures out a secure and convenient way of accomplishing holding these parts in registration, please post. I made a jig to secure the tail board and a 45 degree block to put under the pin board to help hold it in place.

There is not the equivalent of bashing a snug dovetail together like for a square box. They will either slide together by hand pressure or you are screwed. A band clamp will hold the parts in place as the glue sets. It is helpful to not strive for flauntable dovetails to be shown off to friends and family. My goal was to make a box that held together and in that regard the effort was successful.

transfer of pins to tails with aid of jig






Re: Triangular dovetailed box, marking added

#2

Thank you a lot!

Bill Houghton, Sebastopol, CA

Your technical solution posts are much welcomed. I'll be looking for a way to save this one, in case I ever need it.

Re: Triangular dovetailed box, marking added

#3

Re: Triangular dovetailed box, marking added

Derek Cohen (in Perth, Australia)

If someone figures out a secure and convenient way of accomplishing holding these parts in registration, please post.

Bill, I posted my method for this in June last year when building the Apothecary Chest.

Link: http://www.inthewoodshop.com/Furniture/ApothecaryChestWeekend8.html

While the drawers are not triangular, I had to deal with steep angles to fit a tightly curved bow-fronted chest.

What I realised was that there was another way to dovetail other than angling the baseline - instead find a way to square the baseline where the parts meet ...


Two corners of a triangle could be done like this ..


There were two strategies that helped hold the tail- to the pin board. The first was using blue tape to mark out - this requires a single light knife stroke to sever the tape and leave behind an outline. The second was coming up with an alternative to the "#140 trick" (rebate), made popular by Rob Cosman, who used this to align board ends. My alternative uses a couple of layers of blue tape to create a fence ...


The blue tape further acts as a non-slip. The parts are much easier to manage, even though this looks awkward ...


Marked and sawn ..


Parts fitted ...


The other side of the drawer, which used a rebate, came out like this (a note - both these joints were test boards) ...


Both boards/angles ...


Link for this: http://www.inthewoodshop.com/Furniture/TheApothecaryChestWeekend9.html

Regards from Perth

Derek

Re: Triangular dovetailed box, marking added

#4

Re: Manuel de Falla Might Need One

William Duffield

Thank you (and Derek, too) for the useful tutorial(s).

Yes, there are uses for three cornered dovetailed boxes. The first one that crossed my mind is a flag box. My wife has one, but it is not dovetailed, so useless for this discussion.

This is a hat box for a tricorn hat, owned by the Chester County Historical Society.


I wish I had gotten better pictures of the dovetailed joints. You can see it if you visit their museum in West Chester, PA. I'm pretty sure Bill has been there, researching Line and Berry. They have an extraordinary collection of Pennsylvania spice boxes.

I suspect 60° dovetail corners are easier than 45° corners, even if the concepts are very similar.

Re: Triangular dovetailed box, marking added

#5

thanks

Bill Tindall, E.Tn.

I had not noticed that box. BTW, if anyone is visiting this ever improving museum they have a bunch of interesting stuff in the basement that can be viewed by prior arrangement. In addition to spice boxes there are numerous case pieces and clocks. And the sandwich/lunch shop about a block up the street is excellent.