Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

flattening the back

Posts

flattening the back

#1

flattening the back

Jeremy Osner

Thanks for the advice, I have gotten a soft Arkansas stone and started using it for the first time yesterday in flattening the back and bevel of a 3/16" mortise chisel.

I was sure able to see my progress as I worked. I guess this is due to looking more closely than I have in the past. It was easy to see the difference between the flat steel that the stone had touched and the rough steel where the stone was not hitting yet.

I haven't got this chisel quite sharp yet. I noticed in the course of flattening that there is a very slight microbevel on the back of the chisel. it is probably a 1/2 mm back from the edge of the chisel and a small fraction of a mm away from the flat of the back. I think I am going to need to take some material off the back to address this, I'll use 120, 220, 320, 400 grit sandpaper on glass to do that and then go back to the stones.

Re: flattening the back

#2

Re: flattening the back

david weaver

For a back bevel that short, just leave it alone for now and gradually sharpen it off from the bevel side.

Older chisels are often beat up near the edge leaving something rounded over on both sides. A reasonable job of flattening leaves a little bit of that left, and you can just grind it off instead of flattening that much more of the back off to remove it.

Re: flattening the back

#3

Re: flattening the back

Jeremy Osner

So when I'm sharpening it now, with the back bevel still there, should I sharpen the microbevel on the stone?

Re: flattening the back

#4

Re: flattening the back

Bill Tindall, E.Tn.

There are better places to worry about sharpening than a mortise chisel. A mortise chisel is smashed with a mallet. I doubt you could tell the difference between dull as a hoe and plane blade sharp in practical mortise bashing. That chisel is not going to care what it is sharpened with nor notice any difference in details of refinement.

However, take care on the back if you find you need to do anything to it. It is easy to get a narrow chisel out of square and not flat.

Re: flattening the back

#5

Re: flattening the back

david weaver

No, it'll persist if you sharpen it. Just ignore it for now if you don't want to joint the edge off and re-cut the bevel.

If you're using a reasonably fine stone for your final polishing, you should be able to strop any wire edge off (normally, if you have a wire edge, you'd rely on polishing the back to hone it off or push it back over to the bevel side).

Re: flattening the back

#6

Re: flattening the back

William Duffield

Bill is right. A small back bevel is insignificant in a mortise chisel. It would be major PITA in a paring chisel, where the cut is often indexed off the back face, and extends that surface of the wood. In that case, a back bevel would lift the chisel away from the desired cut.

Re: flattening the back

#7

Re: flattening the back

Warren in Lancaster, PA

A mortise chisel is a precision instrument. We don't bash them or smash them. The bevel needs to be flat because we ride the bevel when excavating, and the back needs to be flat because we ride the back when making precise end cuts.

There is a reason why the mortise chisels in the Seaton chest average 11 pence and the firmer chisels average 4 pence apiece. It is because of the precision and care needed to make a functional tool. It is not because the mortise chisels have more steel or more iron; the widest mortise chisel is 1/2 while the firmer chisels go up to 2 inches wide. And the heavy socket chisels, 1/2 to 1 1/4, are likewise cheaper than the mortise chisels.

In the Sheffield list, a 3/8 mortise chisel costs twice what a 1 1/2 firmer chisel does.