Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Request your opinions *LINK*

Posts

Request your opinions *LINK*

#1

Request your opinions *LINK*

Wiley Horne

Hi all,

I need to make a repair to a Bedrock plane, and I’ve not done this particular fix before and would appreciate your help. The repair is to replace the lateral lever. The one that came with the plane is missing its dorsal fin, and was falling-out loose. The Bedrock is a Type 6 (1912-21). I bought an older lateral lever that looked very handsome.

Here is the Bedrock frog. It is positioned over a hammer head serving as an anvil. The post in the center attaches the lateral lever to the frog. The key thing is that the post end needs to be peened enough to affix the lever, but loose enough that the post will still turn in the hole to provide the lateral action.

https://www.flickr.com/photos/78661951@N07/48729828336/in/album-72157710831982303/

There are three punches shown: from the bottom, is a center punch, then a small nail set, then a little larger nail set. Here is a closeup of the three punches in relation to the post:

https://www.flickr.com/photos/78661951@N07/48730007927/in/album-72157710831982303/

QUESTION: How would you go about the peening? Left to my own devices, I would use the center punch or the smaller nail set to tap around the periphery of the post, a little ways in from the edge and angled out a little, trying to flare the very end of the post while leaving it free to rotate.

But I haven’t done this job before, and have no machinist experience. Any opinions on how to proceed?

Thanks, Wiley

https://www.flickr.com/photos/78661951@N07/albums/72157710831982303/with/48729828336/


Bedrock frog & lateral lever

Re: Request your opinions *LINK*

#2

Modification needed

Derek Cohen (in Perth, Australia)

Wiley, I would modify the widest punch you have so that the end is flat. Simply grind a flat face. If you do not have a circular sanding wheel, then use your Tormek.

The nail punches you have are hollowed to avoid slipping on the head of a nail. My concern is that the hollow will cut into the iron rather than peen it over. A wide and flat face will push the steel instead.

Place the flat head half on/off the edge of the pin. Gentle taps around the circumference. You could finish with a wider nail punch once this is done just to even it up (think of a Japanese chisel hoop setter).

Regards from Perth

Derek

Re: Request your opinions *LINK*

#3

Re: Modification needed

Wiley Horne

Thanks Derek. Followed your advice, except for the modification. Worked fine. The modification would have made for a neater job, but the post was soft enough that there wasn’t much to it.

Thanks again, Wiley

Re: Request your opinions *LINK*

#4

Re: Request your opinions

Bill Houghton, Sebastopol, CA

If I recall correctly, I've done it at least once with a pop rivet. Aluminum pop rivets are fairly soft, so, once it had popped, it could be tapped flat on the "back" side without much hazard to the frog.

Re: Request your opinions *LINK*

#5

Re: Request your opinions

Hank Knight

Wiley, you have apparently already accomplished your repair. Good. For what it's worth, I've done this repair before by resting the head end (back side) of the rivet on the horn of a small bench anvil I have and gently and carefully tapping the post (the business end of the rivet) with the ball end of a small ball peen hammer. I probably didn't get perfect symmetry on the mushroomed end of the rivet, but it worked just fine and has held up well for a number of years.

Re: Request your opinions *LINK*

#6

Re: Request your opinions

Wiley Horne

Thanks Hank, you’ve got more courage than me. I was sure I would crack the frog with a mis-hit if I tried.

Wiley

Re: Request your opinions *LINK*

#7

Re: Request your opinions

Wiley Horne

Bill,

Do you have rivets and a rivet tool always on hand? It’s something I’ve never owned—is there a kit you recommend having, or does every application need something different?

Wiley

Re: Request your opinions *LINK*

#8

Jack Guzman from Maine

pop rivets

Jack Guzman from Maine

These are automotive tools. Any auto parts store will have both rivets and a riveter. The tool is quite simple so cheap ones can be had. Many hardware stores also carry these.

Re: Request your opinions *LINK*

#9

Re: pop rivets

Derek Cohen (in Perth, Australia)

Wiley, do not be tempted to use a pop rivet gun on a Stanley plane! These tools do not adjust the force with which they join the rivet and its head. It is all-or-nothing. Not only is it possible to over stress the parts, but connection will end up so tight that it will be locked and immovable.

Riveting by gentle hammer blows is a better way to go.

Regards from Perth

Derek

Re: Request your opinions *LINK*

#10

Re: Request your opinions

William Duffield

I use pop rivets on sailboats and on sheet metal (e.g., ductwork), but like Derek warns, I would never use them on a cast plane frog.

Make sure the back end of the rivet is very firmly backed up by your anvil, and make sure you only hit the front end of the rivet. You should never hit the frog itself with either the hammer or the anvil.

If it is a brass frog, that is different. Send it back to Lie-Nielsen. They will fix it for free. :)