Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

3v meets suita

Posts

3v meets suita

#1

3v meets suita

David Weaver

Commercial Photography

Commercial Photography

I received two things in the mail yesterday. First, the 3v iron that Wiley sent me, and second, a white suita from Japan. The first is a high class item, and the second is high class only in use. I have gotten really good at spotting primo fast cutting stones from pickers and this one cost the princely sum of $52 plus $25 shipping through a proxy service.

It cuts the 3v well. This is the type of stone that makes a good judge of hardness because it will cut even something like this, but it will run out of steam and cut slowly by the mid 60s, even on plain white steels.

I wanted to see if it would remove the spider webbing on the back that is probably due to some stray diamond particles or contaminants.

Re: 3v meets suita

#2

Re: 3v meets suita

Wiley Horne

Amazing stone! Really did clean up those diamond scratches. Maybe you ‘ll be able to see thru microscope how well it will refine the diamond scratches on the cutting edge, too!

Wiley

Re: 3v meets suita

#3

Re: 3v meets suita

David Weaver

For novelty, I'll sharpen the iron with this stone freehand before I give it the test setup of honing guide with back bevel. I think technically the stone probably cuts all of the particles except the volcanic ash (natural aluminum oxide) probably just rubs the vanadium a little and won't fully refine the edge like diamonds will.

Are you OK with me grinding off the back bevel that's already there? I will grind with CBN so that there isn't any significant heat. Flattening that out to restart would be quite a bit of work vs. just grinding it perpendicular and then resetting the bevel.

As far as the result of "less than perfect" sharpening with natural stones, I get a very good working edge on almost everything so far if I have a natural stone except for the SGPS and A2. the SGPS seems to hate almost everything (but loves the deburring wheel followed by a charged buff), even some substrates, and the A2 really hates the washita.

Though nobody's asking, I have probably bought 150 stones from japan and resold most of them (not really making any money, just giving people a relatively cheap source for a graded stone). I find sellers who list less than full size and length stones (sometimes they're full size), but who sharpen something on the stone. If a stone like this comes up (it's a 1kg stone, not tiny by any means, just not full length - it's still a lifetime stone for someone who uses it with care) and it shows a pure black heavy coloration on the surface, you can almost guarantee it will be a very strong cutter. Especially if the seller shows the result of cutting on various stones - you can see which are strong, and which might be less strong or softer by the slurry on the surface.

I hate to say it, but this has been even more reliable than some of the mid-cost dealers that I've dealt with who are selling only new stones. I do have stones that were up to about $800, but faster cutting slightly less fine stones like this (I'd guess 10k grit equivalent on synthetics) you can use without being worried what will happen with them and they are the type where you can sit down, cut rows of half blinds and keep a japanese chisel sharp with one stone indefinitely. A real treat.

My favorite razor stone so far is a bench stone that was flipped by an antiques dealer. It had a weak very old stamp on the end and ended on auction for $35. Not all of the inexpensive ones are good, but the cost of the used stones makes it not much of a risk.

The feel of a stone like the one in the picture is something that synthetics can't duplicate. The only thing that comes close is a frictionite (which isn't really that fine cutting of a stone and the bench stones (#825) are very expensive if you can find one). They do have a superbly dreamy feel, just like a suita, but are not really suited for bench work.

Re: 3v meets suita

#4

Re: 3v meets suita

Wiley Horne

David,

Go ahead and grind it back. I’m real curious what you can do with it.

Good observation on the feedback from natural stones. You can really tell what’s happening at the edge.

Wiley

Re: 3v meets suita

#5

Re: 3v meets suita

David Weaver

Commercial Photography

This shaving is about a thousandth thick, but surface quality is good, reasonably bright without much evidence of plane direction.

Ration for sharpening was fine India to hard ark to suita. The hard mark makes for an ok edge, but the wire edge is very persistent on a natural Oilstone so it's not really a good finisher.

A suita that slurries a little is good for impeding wire edge formation and they don't mind if a little residual oil is on the iron as long as it's not much.

I didn't stick with the tiny thin shaving because the adjuster can't reach the cap with this iron thickness and it loses its set a little depth wise without it.

Tiny diamonds will ramp the sharpness up another notch, but this stone is practical and quick as a freehand finisher for this iron. I'll pein a tab to the cap iron to use this or buy a lie Nielsen plane for testing.

The grind was cool and uneventful with a cbn wheel.

Re: 3v meets suita

#6

Re: 3v meets suita

Wiley Horne

Geez louise, why didn’t I send you the plane with it?! For some reason, I thought you had every plane on earth :) :) . If you’d rather not own an LN 4.5, 5.5, 6, or 7, I’ll send you my LN5.5, this afternoon or Monday morning. Lemme hear something.

Wiley

Re: 3v meets suita

#7

Re: 3v meets suita

David Weaver

No need for the shipping expense, Wiley. I no longer have any big LN planes, just a 4 bronze, but I'm sure that I have an infill that will fit that size, even though it's not typical.

Actually, my favorite cast infill is this same size. It was something someone in the UK put together from a hardware store kit (I think) and is the best working panel plane I have, bettering my two norris panel planes.

If not, I'll pein something on the record plane that I have. This is a minor issue definitely not worth a double expense of shipping (Which is at least as much as I'd lose if I just outright bought a new LN and sold it at the end).

Thanks for the generous offer, though. It's never required and always appreciated.

Re: 3v meets suita

#8

Found a suitable plane

David Weaver

Commercial Photography

A 2 3/8 infill is probably not common., but thankfully, I have one.