Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Two Questions on Draw knife handles

Posts

Two Questions on Draw knife handles

#1

Two Questions on Draw knife handles

Don Goodwin

I was at a MWTCA tool meet last weekend and purchased a draw knife that was missing both handles. I want to practice making handles for it and also learn how to use a draw knife.

Question 1: I think I remember a post or an article from the last couple of years that had a really good and detailed write-up on making handles for a tanged draw knife. I tried searching for it, but I can't seem to find it. Does anyone recall this or have the link? I thought it was by Derek and looked at his site, but I couldn't find it there either.

Question 2: I was trimming my apple trees today and cut off a couple of large limbs. Can these be turned into handles while green and dry on the draw knife without issue or do I need to rough them out and then let them dry for a period of time before mounting?

Thanks,

Don

Re: Two Questions on Draw knife handles

#2

Re: Two Questions on Draw knife handles

Philip Duffy

One of the experts can tell you more but my instinct is that green wood might split. You could cut the pieces in ruff, microwave them til dry and then mount. Plans? Isn't that your choice? Mine have flats but no one else seems to have anything but round handles. P

Re: Two Questions on Draw knife handles

#3

Re: Two Questions on Draw knife handles

Wiley Horne

Hi Don and all,

I seem to recall John Aniano making a wonderful set for Brian Holcombe, and posting detailed photos.

If that’s right, maybe someone here knows how to find the original posting.

Wiley

Re: Two Questions on Draw knife handles

#4

Apple

Bruce, a MN Galoot

I don’t know where the saw tote makers of your got their apple, so big and split free, but I sure can’t find any. I got a piece of apple from a friend, and it checked badly. I would wait until it fully dries.

Re: Two Questions on Draw knife handles

#5

Sure

Warren in Lancaster, PA

There is no problem using green wood for this. I recommend splitting a branch down the middle or into quarters to get nice stock. A piece of a branch that contains the pith is vulnerable to heart checks. If the pith is near the edge of your stock, it will probably split from the pith to the nearest edge, but will otherwise be sound.

An apple branch that grew at an angle will have compression wood on the underside. This is a form of reaction wood. The tree makes extra wood on the underside of the branch in order to counteract the tendency for the branch to droop and there can be three or four times as much wood on one side of the pith as the other. Also such a branch can distort a bit when it is cut open.

Green wood cuts cleanly with sharp tools; I don't recommend filing or sanding.

Re: Two Questions on Draw knife handles

#6

On to plan B

Don Goodwin

Thank for the suggestions. After cutting a section from a branch and splitting it, it appears that the center pith is too large to get any useful wood out of it. I happened to have some mulberry out in the woodpile and I think it has better wood.










Re: Two Questions on Draw knife handles

#7

Re: On to plan B

Warren in Lancaster, PA

I think what you are calling the pith is the heartwood, which is fine. The heartwood is a reddish brown as opposed to the sapwood, which is creamy. The pith on an apple tree is about 1/16 inch in diameter. It would be hard to find if it were not at the center of the annual rings.

Re: Two Questions on Draw knife handles

#8

Re: Two Questions on Draw knife handles *LINK*

John Aniano in Central NJ

Hello Don

Here is the link to how I made a pair of handles for a drawknife. It was a post by Brian Holcombe. I made the handles from fully seasoned wood.

And for general info, to search within the Wood Central website (how I found this link) use the following syntax within a search engine:

site:www.woodcentral.com drawknife handles

So, "site:" "www.xyz.com" without spaces between the : and the www and then a space and then the search phrases.

John


http://www.woodcentral.com/woodworking/forum/handtools.pl/md/read/id/485047/sbj/draw-knife-handles/

Re: Two Questions on Draw knife handles

#9

Re: Two Questions on Draw knife handles

Don Goodwin

Yes! That is the post that I was looking for. Unfortunately, I was using "draw knife" (with a space) in my search and missed Brian's post. I'll remember next time to try different variations on drawknife, draw knife, drawknives, etc. We have bad weather today, so I'll head to the basement and play.

Thanks again for the various helpful comments