Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Telecaster Style Guitar - Maybe 80% by hand?

Posts

Telecaster Style Guitar - Maybe 80% by hand?

#1

Telecaster Style Guitar - Maybe 80% by hand?

david weaver

My second guitar. It's difficult to make a contemporary instrument look contemporary without using any power tools I've routed the cavities in this guitar, the roundover on the back and the binding channel, as well as cleaning up the curves initially with an OSS. One would normally rout the outside of the body, but with spruce, it's a risk, so most of the bulk work was done by hand with a spokeshave, rasps or scrapers, then OSS right to the line, then back to hand finishing to remove any unevenness.

Everything else (the entire neck, fingerboard, etc, sizing the lumber, all cuts) is entirely by hand.

I did attempt two guitar bodies without power tools, and they end up looking too rustic (not in proportion or curves, but the lack of refinement at the binding channel, especially. An archtop guitar would be far more doable without power tools - especially if you didn't bind the body (think violin) but installed stringing away from the sides.

Sitka spruce body, cherry neck, birdseye maple fingerboard. Waiting for the finishing bits (on the fence for the top coat - shellac or varnish that I cooked from pine and damar resin. The latter is more permanent, but it needs sunlight to cure quickly - three weeks for each coat without it vs. one good day in the sun ). The rest to go on/in the guitar at this point after finish is just hardware.

My routing template for the cavity doesn't ever seem to line up with the pickguard (the round control plate needs to fit neatly in the cutout on the pickguard), thus the two gouge cuts to make room for pots under a control plate. All of that is covered in the finished guitar, so it's meaningless. I usually cut that cavity last to try to line it up, but it's never quite right - the template is further off than that.

https://i.imgur.com/JNniIzu.jpg

https://i.imgur.com/vBugUyY.jpg

https://i.imgur.com/KVBeps4.jpg

I briefly joined a guitar forum late last year to start making guitars, but didn't find people doing much by hand. Some of the attempts to build jigging to do precise work without hand tools were mind numbing, and the attempt to use sandpaper and power tools to do finish work led to some ugly surfaces and nasty proportions.

Planemaking tools come in really handy cleaning up the curves and fitting the neck pocket (which would be tedious to get perfect with a router - the details to do all of that right are not what I'm looking to do when I go in the shop). Much faster and easier to cut a rough pocket short of final size and then finish by hand and fit the neck to it.

Re: Telecaster Style Guitar - Maybe 80% by hand?

#2

Re: Telecaster Style Guitar - Maybe 80% by hand?

Charles

Looks good David. Nice work. How does she play?

Re: Telecaster Style Guitar - Maybe 80% by hand?

#3

Re: Telecaster Style Guitar - Maybe 80% by hand?

david weaver

It'll be another couple of weeks (if varnish) or another week (if shellac or lacquer) before I get hardware on it permanently and string it up, but when you're building a guitar (at least of this type), it's easy to make one that plays well and sounds great through an amp. You can pretty easily do the things that are sped through or skipped at the factory due to cost (cutting nut slots to gauge height rather than leaving them a little high for safety margin, leveling frets and crowning and polishing them). Machines (CNC and PLEK) are catching up, though, and machine-done attention to those things is starting to make it onto inexpensive guitars ($1,200 and below).

Total hand time in a new guitar made in a factory is probably a couple of hours, mostly light sanding and then paint prep and buffing. Completely different concept, I guess - paint color and quality of the bondo work on cheap wood is worth more than trying to source good wood and do little to it.

There are some people down your way still making guitars (of this type) in smaller numbers with more hand work, but not many. I have no clue how they find customers, but that's the number one challenge. Building difficulty is *nothing* in these compared to building good furniture.

Re: Telecaster Style Guitar - Maybe 80% by hand?

#4

Re: Telecaster Style Guitar - Maybe 80% by hand?

GolfSteve in Calgary

That spruce body looks great!

Re: Telecaster Style Guitar - Maybe 80% by hand?

#5

I’d love to get my hands on that axe


Re: Telecaster Style Guitar - Maybe 80% by hand?

#6

Re: Telecaster Style Guitar - Maybe 80% by hand?

David Weaver

Lucky break to find the blank on ebay for $50, and it had enough thickness to yield a top for an acoustic, too.

Re: Telecaster Style Guitar - Maybe 80% by hand?

#7

Re: Telecaster Style Guitar - Maybe 80% by hand?

Charles

It would be a heck of a niche to develop.

Re: Telecaster Style Guitar - Maybe 80% by hand?

#8

Re: Telecaster Style Guitar - Maybe 80% by hand?

david weaver

Like lots of things in the world of making, eh? The most important skill if you want to make more than $10 an hour is building your market, making what they want rather than making what you want to make.

And maybe overselling what you're doing a little bit and playing coy.

Many makers of telecaster style guitars and other easy to make instruments that bounce out of regular jobs and bounce back in once they run out of money.

Re: Telecaster Style Guitar - Maybe 80% by hand?

#9

Re: Telecaster Style Guitar - Maybe 80% by hand?

Charles

Challenges aplenty, that's for sure.

Re: Telecaster Style Guitar - Maybe 80% by hand?

#10

Re: Telecaster Style Guitar - Maybe 80% by hand?

Brian Holcombe

That’s gorgeous!

The detail around the peg head (am I correct in this terminology?) are nice and crisp.

Nice wood choices, the spruce is really clear and perfect.

Re: Telecaster Style Guitar - Maybe 80% by hand?

#11

Re: Telecaster Style Guitar - Maybe 80% by hand?

david weaver

Thanks, Brian - yes on the terminology. Commercial guitars are usually neatly made, but they're sanded pretty hard, so that crispness is gone.

The exchange in my case (that I'd have corrected if I was selling it) is that there is a light scraper mark or two in some places that shows up once varnish is applied. It would've been easy to correct (same with the little dark spot at the bottom of the binding - the binding is cellulose, and it flows into problem areas - that would've been corrected if the guitar wasn't for me, but I don't care so much about it (it can always be fixed later).

Waiting for a sunny day, as the bits are hanging in the garage with varnish on them - three weeks and they'll cure inside. One sunny day, and they'll be 90% cured outside.

Looking forward to doing more complicated guitars that take longer to make and have more hand work in them.