Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Hand plane set up question

Posts

Hand plane set up question

#1

Hand plane set up question

Barry Irby

I bought several hand planes at an auction. One is a Union 14" long. Sharpened it and cleaned it. put ti back together and tried it out. Chips went between the blade and the cap Iron. (???) They appear to mate well with the cap laying very snug on top of the blade. What am I doing wrong and how do I correct it?

Re: Hand plane set up question

#2

Re: Hand plane set up question

david weaver

Check and make sure that the mating of the edge is right at the very edge, with some relief behind the front of the cap iron.

Sometimes, some cap irons (without additional manipulation) just don't do a very good job of keeping the chips out.

If the knife edge fit is at the front of the cap with decent relief and the lever cap is reasonably tight and the whole assembly still doesn't work, you can experiment. However, I think given the cost of #5 planes, it's more practical to just write such a plane off and use it for coarse work with the cap iron set off of the blade a little bit.

Nearly everything can be fixed, but sometimes it's more effort than it's worth if you have an alternative.

If you have easy access to another cap iron and blade (from another plane) that fits, you can test that. It would be a good way to confirm that it's the blade and not something else.

pictures always help, too, if you want to pursue fixing the plane. (and make sure the mouth is opened up enough to avoid any issues with that - a 16th gap with the cap iron set close is preferable to ensure that there isn't a jam up adding to the problem).

One other aside - once in a while, you'll run into something with giant beam strength (larry W's word) that can just work its way under the cap in a heavy cut. Flatsawn cocobolo comes to mind - the late wood is so hard that it can go under like a putty knife slipped into a joint.

Re: Hand plane set up question

#3

Jack Guzman from Maine

Re: Hand plane set up question

Jack Guzman from Maine

It's pretty easy to tighten up a chip breaker. I usually sharpen the edge a bit on a sharpening stone. It doesn't take much of a gap to allow shavings to grab. http://www.woodcentral.com/cgi-bin/readarticle.pl?dir=handtools&file=articles_120.shtml

This is an article here at woodcentral on tuning a hand plane

Re: Hand plane set up question

#4

Re: Hand plane set up question

William Duffield

When you tighten the chip breaker screw, it can flex the chip breaker enough to open a small gap between the front of the chip breaker and the blade. The easiest way to fix it is to lay the front quarter inch or so of the chip breaker on your stone and the back end on the bench that is supporting the stone, with the surface that meets the blade down against the stone. This preferentially removes metal from the back edge of the mating surface. Then simply hone the chip breaker back and forth until the mating surface is flat. Use a Sharpie marker if necessary to indicate when you have achieved flat.

Since I'm not near my shop and camera right now, I found an image on the web that is illustrative:


Re: Hand plane set up question

#5

Reference to Sir Wm’s photo

Wiley Horne

Barry,

A key thing to know is that the cap iron (chipbreaker) must be undercut. This happens when you are sharpening/flattening the edge. As shown in Mr. Duffield’s photo, the cap iron is positioned on the stone in a way which will undercut the edge. Thus, the cap iron will meet the iron, not flush, but on a knife edge. The undercutting of the knife edge allows for some flexing of the cap iron when it is tightened.

Wiley

Re: Hand plane set up question

#6

Re: Reference to Sir Wm’s photo

William Duffield

Thanks, Wiley, for the additional enlightenment.

When you understand something, it is often difficult to realize what those you are trying to explain it to, do not know. And, it seems that the longer you have known something the worse it gets. I sometimes think the best time to teach a skill is just after you have learned it yourself.

The chip breaker sharpening technique is kind of like the opposite of the "ruler trick" except you may need to remove a lot more material. ;)

Re: Hand plane set up question

#7

Re: Reference to Sir Wm’s photo

david charlesworth

That's a good photo.

A fine diamond stone is useful as the surface will stay flat.

I would suggest that the top of the c/b is supported on a small prop (stick of wood) which is 3mm lower than the surface of the stone.

This gives an undercut of approximately one and a half degree.!

A nice pilot who spent time here taught me the one in sixty rule, 1:60 is about one degree!

Black felt tip or Sharpie is good for monitoring progress.

happy new year,

David