Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A coffee table for my nephew - #6

Posts

A coffee table for my nephew - #6

#1

A coffee table for my nephew - #6

Derek Cohen (in Perth, Australia)

We are at the stage where the base - rail with tapered and splayed legs - is to be done next. This is the photo of the model ...


I like this base, and have chosen to replicate it. The two relevant items are the angle of the splay (which I estimated as 10 degrees), and the positioning of the ends of the legs (these appear to end in line with the carcase).

I get my Jarrah these days from an urban salvage yard, but some of it is ex-roofing beams, like this ...


It is a wonderful moment when it comes out the other end ...


I planed up a couple of these to find 4 blanks that would make the legs. Each is 450mm long. The legs will taper in the round from 40mm at the top to 25mm at the bottom.

The mortices were marked out ...


... and routed out (I have a great jig for this - just made for hard, hard woods) ..


.. leaving ...


The ends of the mortices are squared up ...


.. and then onto the lathe ...


A little tinted epoxy is needed to repair some of the resin holes ...



Next step is to determine the length of the rails. This is a no-math process that simply involves laying out the parts, with the legs at 10 degrees ...



Sawing the tenons is easy enough. The rails are 19mm (3/4") and the tenon/mortice is 1/4" wide ..


The tenon shoulder needs to be fitted flush with the leg ...


The easiest way is to use blue tape to mark the shoulders ...



The shoulder of the mortice is levelled with a chisel and rasp ..


... until each is a good fit ..


Finally, the glue up begins ...



I pulled off the clamps a short while ago ...


I'll clean it up in the morning.

Regards from Perth

Derek

Re: A coffee table for my nephew - #6

#2

Re: A coffee table for my nephew - #6

Philip F Duffy

Derek, Once again you have shown all of us how to do wonderful workmanship! Thank you. P.

Re: A coffee table for my nephew - #6

#3

A coffee table for my nephew - #6

Tom Colligan

Many thanks for the write-ups on your project(s), Derek. They are well read, I'm sure.

With your next posting how 'bout a picture of the mortice jig you use with the router? There's a couple of variations of these out there but I'd like to see what you developed. Thanks again, Tom.

Re: A coffee table for my nephew - #6

#4

The mortice jig *LINK*

Derek Cohen (in Perth, Australia)

Hi Tom

The jig essentially consists of a method of trapping the plunge router to travel in the direction desired, along with a set of clamps to hold the work piece. The advantage of this design is that it is set up very quickly and is very reliable. The track is to set up stops.

The idea came from Fine Woodworking magazine. My only modification was to change the clamping system. The Matchfit clamps (by Microjig) slide into dovetails. These are more flexible and adjustable than the clamp on the FWW model

Video link to FWW: https://www.finewoodworking.com/2015/05/27/how-to-cut-mortises-with-a-plunge-router

My version ...




I briefly owned a mortice machine, and quickly sold it. This router-based jig is far easier to maintain (than sharpening augers). Since it works from above the workpiece, it is easy to work accurately. All very intuitive.

Regards from Perth

Derek


Matchfit clamps

Re: A coffee table for my nephew - #6

#5

Re: The mortice jig

AZ in Colorado Springs

Derek, what do you use the t-track for?

Re: A coffee table for my nephew - #6

#7

Re: The mortice jig

AZ in Colorado Springs

Doh ... I should've realized that.

Thanks

Re: A coffee table for my nephew - #6

#8

Re: The mortice jig

William Duffield

Note that Festool (and several other makers of track saws) also sell the equivalent of the MatchFit clamps, for about the same price. In addition to using them in dovetailed slots in wood, they will also slide into most varieties of T-track (but not Kreg's) and also into the bottom slots of tracksaw tracks. So, you can also use the clamps instead of t-bolts and threaded knobs to hold your end stops in place.