Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Question on fitting Half-blind Dovetails

Posts

Question on fitting Half-blind Dovetails

#1

Question on fitting Half-blind Dovetails

Don Goodwin

Looking for advice on what, if anything, I can do to fix the gaps? Will "shortening" the tails on the right side (top of the image) tend to close the gap between the two boards? This is the top to the side upright joint of a 6'-4" clothes rack, so it won't really be visible, but I will know it's there. Obviously, I need more practice on hand cut dovetails.

Note: I could not get the image to rotate. This photo is 90 degrees off. The top of the image is the right (or back) of my workbench, the thick board on the right side of the image is my benchtop.


Thanks in advance,

Don

Re: Question on fitting Half-blind Dovetails

#2

Re: Question on fitting Half-blind Dovetails

Alan S

No. If you shorten the tails, you wind up making them narrower at the end, so you open up gans on the gluing surface.

If you glue a bit of veneer to the pins, it will fill the space, making the tails fit snugly. Or you can use some sort of filler/veneer shims to directly fill the gaps.

Re: Question on fitting Half-blind Dovetails

#3

Re: Question on fitting Half-blind Dovetails

Alan S

"gaps" not "gans".

Re: Question on fitting Half-blind Dovetails

#4

Re: Question on fitting Half-blind Dovetails

david weaver

Clamp the front tight to the sides and glue. Make yourself some small veneer shims to insert adjacent to the tails so that if the glue fails in the future, the tails will still pull the drawer front tight mechanically. Once your shims are in, if you have other small gaps and the unsightliness still bothers you, rather than faffing around too long, take some dust or shavings and make a paste with glue and push it in.

It's not going to look like perfect pins and tails, but it'll be mechanically sound and be an improvement.

And then don't worry about it.

Re: Question on fitting Half-blind Dovetails

#5

Re: Question on fitting Half-blind Dovetails

Don Goodwin

Thank you for the suggestion to fill the gaps. I'll do that with slivers from scrap wood and not worry about it.

Thanks,

don

Re: Question on fitting Half-blind Dovetails

#6

Re: Question on fitting Half-blind Dovetails

Brian Anderson

I would check the layout lines for square.

Check the cuts to the layout lines.

Check the bottoms of the sockets for square.

The 3rd tail appears as though it might be bottomed inside.

Some pins appear to be short as well.

But I only have pix that are not real detailed.

I also would check the tail board for square to edge and face.

Any deviation could wind up holding the fit up.

Re: Question on fitting Half-blind Dovetails

#7

This may be fixable

Derek Cohen (in Perth, Australia)

There are a number of even gaps. These suggest that there is an obstruction holding the tail- and pin boards apart. The most common reason for this is either a failure to clear the corners of the pins, or sloping pin baselines. In other words, something obstructing the clean joining of the mating parts. Check for these before inserting filler pieces.

Regards from Perth

Derek

Re: Question on fitting Half-blind Dovetails

#8

Re: Question on fitting Half-blind Dovetails

Clementine

My two cents: Instead of glue and sawdust I read an article that recommended shellac and sawdust because shellac will take a stain and glue doesn't. Not saying this will solve the fitting issue, but just something to file away for a future situation. Actually, if my handcut dovetails fit as well as yours, I'd be thrilled enough to show the wife.

Re: Question on fitting Half-blind Dovetails

#9

Re: This may be fixable

david weaver

Derek makes a good point that I neglected to - my first order of business would be clamping the whole thing from the back until the tops of the tails were against the sockets nearly flush. If they aren't, then do a little bit of work to remove any obstruction preventing that. Once the ends of the tails and sockets are flush, you can do pretty easy work to make them look decent, and then maybe consider what caused the issue to improve on the next set.

What you learn from shimming/fixing, may not be something you do much of in the long term, but at some point, you're going to sink time into a well-fitted set of dovetails with one or two of the problems (vs. the same issue across the board like this). Tasteful fixing is as important as any other skill.

Re: Question on fitting Half-blind Dovetails

#10

Re: Question on fitting Half-blind Dovetails

John Pappas

Don, I know you asked about fixing some gaps. May I make a couple of points to help you avoid the gaps? Assuming you do tails first; when you mark the pins, keep in mind that the pencil line you make is the edge of the pin....saw to the edge of that line...., not on the line. Second point is about chopping out the waste. If you place the chisel right on the baseline and smack it hard, the bevel will force the chisel back passed the line. You can make the first chop away from the line and then chop to the line, or you can make a light cut on the line to establish a wall. Once the wall is established, you can get more agressive. Hope this helps.