Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Craftsman Plane

Posts

Craftsman Plane

#1

Craftsman Plane

David Skibbe

I came across a plane that belonged to my father and decided that it needed to be brought back to life. It's a Craftsman 619-3741 and have learned some about it's history, but if anyone can add to it I'd be thankful. One of the things I was trying to nail down was it's date of manufacture? And since it has the phenolic resin tote that is broken, does anyone have an idea where I might locate one? Thank, Dave

Re: Craftsman Plane

#3

P. S.

Wiley Horne--So. Calif.

The seller’s estimate of date may be correct, but I suspect the Sargent model numbering refers to plane models, not date of manufacture. Based on blade width, this looks to be a ‘No. 3’ in the usual terminology. The 3742 he refers to could well be a No. 4 type.

Wiley

Re: Craftsman Plane

#4

Re: P. S.

Jerry Nicholson

My Dad's Craftsman plane with a phenolic tote is from 1951 or earlier. I find no part numbers on the plane itself but the cutter has part number 619.3742. I don't know if it was made by Sargent or not but it has a very poor frog design and the cutter is unsupported for more than 1/2 inch at the business end. Kind of like a frog for a transition plane. I have 3 Sargent planes and their frogs properly support the cutter. I also have a Dunlap (cheap Sears grade) from sometime in the 60s and it has the same poor frog design but it does have an unimpressive looking wooden tote.

I was never able to use either of these Sears planes for anything harder than soft pine.

Funny thing about the old Craftsman plane - the sides are corrugated!

Jerry

Re: Craftsman Plane

#5

Re: P. S.

david weaver

If the frog is moved back, will the cutter rest on the casting?

I've had several planes that have that unsupported span (ohio planes come to mind), as well as the initial confusing puzzle that is a transitional plane.

The transitional planes rely on you using the cap iron instead of closing the mouth and they work well as long as the iron is set to bed on the wooden bed.

They can be blocked shut at the mouth if the mouth is too large (by inserting a mouth blank like you sometimes see on old wooden planes), but I've still never liked htem. Some of the older ones have opposite-rotation adjusters, and some have adjusters that are hard to get to, while others (all) have fairly weak feeling handles compared to metal planes with a front screw.

They do have a lot of nice screws in them, and beech for chisel handles if you take one apart and throw away all of the useless bits.

Anyway, the metal plane may become more usable if the mouth isn't too large and the bevel of the iron will rest flush on the casting for support. (still, any reasonable-priced stanley plane that doesn't have those limitations is a good reason to set the craftsman plane aside - same with the ohio or union or KK keen kutter series, or anything else that has a long unsupported span).

Re: Craftsman Plane

#6

Re: P. S.

Jerry Nicholson

It has been so long since I tried to use one of these Sears planes that I don't remember if the frog can be moved back far enough so the end of the cutter would rest against the sole. This would, of course leave a humongous mouth! When I want to do any planing I use one of my old Stanley's (typically with a thick after market blade and a heavy after market chip breaker) or one of my Veritas bevel up planes and the Sears planes stay on the shelf. I keep the old Craftsman because it belonged to my Dad. The Dunlap was a gift from folks now deceased and I have no really good reason to keep it around.

In 1951 my dad and I built my strictly utilitarian desk. That desk has lived in 4 locations and I still sit at it every day. It held my receivers and smaller transmitters during my active days as a ham radio operator (early 50s). I built desks for my kids and I have thought many times about building myself a much fancier desk but just never got it done.

Jerry