Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Danish modern bed joinery

Posts

Danish modern bed joinery

#1

Danish modern bed joinery

steve voigt

After a storm punched a hole in the roof and killed our mattress, we upgraded to a queen-size, and now I have an emergency bed-building project. It has been decided that this is the desired design (I quite like it too).


Having never built a bed, I will probably have a number of joinery questions. Here's my first: What about the tenons going into the front legs, pictured below?


Would you make mitred tenons, or perhaps interlocking tenons, or ? Any input is much appreciated!

Re: Danish modern bed joinery

#2

Advice

Bill Tindall, E.Tn.

I have built a bunch of beds and they are all still in service and still ridged. Those joints will not last the ages no matter the details unless the bed is expected to only have light duty. There are bed builders on the Main Board for additional input.

Something with bed bolts is the only way to build a bed that will never be wiggly. However, you could build that light design. Inside it set a second frame on legs and set the box springs on it. Dangle a dust cover over the frame to cover it. To accommodate the huge span of mattress thickness I have used this arrangement on several beds with success. I just make a frame from bridle joint 2 x 4's and sit it on a 4 x 4 leg.

Re: Danish modern bed joinery

#3

Re: Danish modern bed joinery

Warren in Lancaster, PA

Were you ever on a bed that collapsed? I don't think there are any tenons at all, just screws and lag bolts and steel plates. I have repaired beds that had better designs and failed.

Re: Danish modern bed joinery

#4

Um.....

Bill Tindall, E.Tn.

"Were you ever on a bed that collapsed?" This question may lead to a discussion inappropriate ;) for WC

Re: Danish modern bed joinery

#5

Re: Danish modern bed joinery

Brian Holcombe

Steve,

It's a nice looking design, but I might be tempted to make some modifications to the design in order to allow for some redundancy. Likely those joints are just haunched mortise and tenon that interlock inside of the leg.

If you can build one or two legs under the center of the bed, absolutely do so. IMO one is required and two is better still.

I would also find a way to brace behind those joints, likely an interior frame that also carries the slatted top but manages to work as a way to prevent flexing of those rails.

Make it fairly short, I would imagine that the top of the mattress would be no higher than 17", so the bed frame is probably no higher than 8-9". That is a huge advantage in this case.

Re: Danish modern bed joinery

#6

Re: Danish modern bed joinery

steve voigt

Brian and all,

Thanks for the replies--much appreciated. It seems the unanimous opinion is that the design needs some beefing up, and I agree. However, coming to agreement in my house on an aesthetically satisfactory design is comparable in difficulty to passing an international treaty, so the basic design will stay. :D

I agree with keeping the rails relatively low to the ground. And I was planning to add a center support for the slats, so adding one or two legs under that will be no problem--good idea.

I was also planning to use bed bolts at the back, so the headboard, rear legs, and rear rail will detach as a unit. There'll be an inner rear rail permanently attached to the side rails, to keep the rest of the frame together when the headboard is removed.

Below is the joinery for the rear legs to rails. One modification I'm considering is to use the same joinery for the front legs, but rotated 90°, so that the front rail would tenon into the side rails the way the side rails tenon into the rear rail. That might be stronger (and easier) than the miter-ish joint I showed above. I also think that the rail-to-rail joints should be closer--they look like they're at least an inch from the leg; maybe half that would be better. Thoughts, anyone?


Re: Danish modern bed joinery

#7

Re: Danish modern bed joinery

Brian Holcombe

Ah, I see what you meant now. I would not do that, it will look a bit strange and bang your foot every time you walk past after midnight. I might make the legs stand proud of the rails by 1" so you can run the haunch all the way to the top of the rail.

Re: Danish modern bed joinery

#8

Re: Danish modern bed joinery

steve voigt

Brian,

Point well taken on the foot-banging. And you are probably right on the aesthetics as well. Thanks for the advice!

Re: Danish modern bed joinery

#10

Re: my pleasure!

Jim Matthews

Rather than interlocking tenons, why not make the rails meet in a double bridle joint? Once fitted, a heavy face veneer could then be shaped as you like.

Re: Danish modern bed joinery

#11

Re: Danish modern bed joinery

Sgian Dubh

Side rails are probably attached with hardware similar to the type below. End frames are likely M&Td together. KISS principle rules. Slainte.


img

Re: Danish modern bed joinery

#12

Re: my pleasure!

Brian Holcombe

Not sure I quite understand, could you draw that out?

Re: Danish modern bed joinery

#13

Interlock bridle joints *LINK*

Jim Matthews


Remove the protruding ends, laminate the leg "show faces" with suitably thick shop veneer and shape to desired profile.


http://greenvirals.com/japanese-platform-bed/asian-inspired-platform-bed-by-silverhalo-lumberjocks-com-japanese-platform-bed-great-house-designs-if-you-are-looking-for-inspiration-on-how-to-decorate-your-small-bedroom-check-out-these-fanta-2/

Re: Danish modern bed joinery

#14

Re: Interlock bridle joints

Brian Holcombe

I see what you mean. I would be a bit nervous about those joints in a small size I always find open joints to be wiggly unless they're glued or massive as those are.

Re: Danish modern bed joinery

#15

Re: Interlock bridle joints

William Duffield

In the middle of the night, when navigating where "sleeping dogs lie" that joinery would be a really painful shin cracker.

Since the tops of the post joinery is not tied together, I would be concerned that any torque applied to the rails would have a tendency to split the posts all the way to the floor.

Re: Danish modern bed joinery

#16

Re: Interlock bridle joints

Brian Holcombe

That would certainly spice things up. :D

Re: Danish modern bed joinery

#17

Re: Interlock bridle joints

Jim Matthews

"Remove the protruding ends"...

"Laminate the faces with shop veneer"

No more material will be removed in this method than with the (more difficult to make) tenons.

The sort of overlapping joint in timber framing is strong.

If torque is a less onciderable force on a mattress frame than

splay as the legs attempt to tip inward.

A simple center support eliminates this.

Re: Danish modern bed joinery

#18

Re: Interlock bridle joints

North of the Border

If someone fell near the bed, the injury to the head could be serious, if not fatal. Too blunt a joinery I'd ever consider at that level from the floor.

Re: Danish modern bed joinery

#19

Re: Danish modern bed joinery

TomD

With structures as in the op a huge difference can occur if there is any load sharing with anything else, like a plywood bottom, or a corner block that is hidden.

To make what we see solid you probably could with hardware bonding which is basically WEST grade epoxy, oversized holes and metal dowels. You can get unbelievable strength from that. As in holding 80 foot wood composite wind turbine blades on with 24 1/4 " root studs. I'm guessing 4 in this situation would be plenty strong. Ideally drill the hole so bent studs go well into the post. But one knows they didn't do it that way, and much have had a wood alternative. Maloof used pretty crude metal hardware in his rockers and is possibly our most famous woodworker.