Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

I get around (marking gauge)

Posts

I get around (marking gauge)

#1

I get around (marking gauge)

Bill Houghton, Sebastopol, CA

Alternate post title: Do you love me, now that I can mark?*

Marking gauges with round fences have been all the rage for a few years. I've been feeling out of it/left out because I don't have one :) .

No more. I found this little gem at a yard sale today.


Unlike the modern gauges I see in the catalogs/online, this one has points instead of wheels, but the points are done cleverly: a square shape on the end of the rod, with sharpened corners:


You could get a lot of use from this before you had to stone the corners for sharpness again.

There's no maker's name on it, but it's very well done for a commodity tool. The knurling on the setscrew for the fence is particularly fine. I've been to this particular sale in past years, and purchased machinist's tools; so I suspect this was also a machinist's tool.

Another demonstration that there's not many new ideas under the woodworking sun.

--------

*It is not well known that this is the original title of the song, "Do You Love Me, Now That I Can Dance?" made famous by the Contours. The original song was written by Megan Patfitzrick, a young woodworker celebrating the purchase of her first marking gauge. She first sang it at an open mic night to a total audience of two. Fortunately/amazingly, one of them was Berry Gordy Jr. He recognized the potential of the song, and talked to Megan after the show, asking if he could adapt it for a less obscure audience, and promising co-writing credits. After a little work, Gordy offered it to the Contours (a fitting group's name for a song by a woodworker), who then made it famous. You can hear echoes of the original song in the lyrics, such as "Do you love me/I'm in the groove," an obvious reference to marking out for a groove in a piece of stock. Alas, Gordy lost the napkin on which he'd written Megan's name and contact information, and she never received the recognition or the royalties from the song, and eventually had to scrape out a living editing reprints of Shakespeare poems.

For those not familiar with the song (you're an international member, you're too young, you never paid attention to popular music when you were young, you can't remember a damn thing from your youth), here are a couple of renditions by the Contours:

When they were young: [url]https://www.youtube.com/watch?v=azKPeIWdE6I[/url]

More...grown up [url]https://www.youtube.com/watch?v=LhqmD1aVuNw[/url]

Re: I get around (marking gauge)

#2

Re: I get around (marking gauge)

David weaver

That's an interesting gauge, and a practical one. I'd guess it might fall a bit short in terms of accuracy for machinists use, but it should do well for woodworking.

Some years ago, there was a generous tool dealer near my parent's house, and he had a bunch of Stanley wheel gauges with one stem and two stems. I bought one of each for an average of ten bucks or so. They're not as smooth as modern gauges, and the wheels are not as sharp, but they work just fine unless you need truly fine accuracy to the micron. The only time I've ever wished for more is when making infills, and even then, it's easy to work around as you still have to cut the infills large and slowly trim them to final size.

Re: I get around (marking gauge)

#3

Re: I get around (marking gauge)

Todd Stock

OK - so now you get to sit with the jocks and poms at lunch...but you'll still need to finish a Roubo bench & a Moxon vise before you'll be taken seriously when asking one of the cheerleaders to homecoming, and don't get me started as to what you'll have to do to be considered for the Prom King's Court...it's just degrading, IMO. There's levels to this popularity stuff....kids can be cruel.