Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

3/4 dado plane depth

Posts

3/4 dado plane depth

#1

3/4 dado plane depth

steve voigt

Long shot here, but for anyone who has a 3/4-ish woodie dado plane,* what's the max depth of cut with the depth stop retracted all the way?

I have a 3/8 plane that probably would have cut 1/2 deep when new. I can't see a reason to cut any deeper, even with a wider plane but it would be nice to have some confirmation from vintage examples.

* data from anything in the 5/8-7/8 range would be helpful. Thanks all!

Re: 3/4 dado plane depth

#2

Re: 3/4 dado plane depth

Bill Houghton, Sebastopol, CA

Yes, 3/4" plane, with 5/8" depth of cut.

Mine's been in sick bay since I got it from an estate sale. It had been a screwed-to-the-wall decoration, and it's missing the nicker iron and a workable wedge (head's broken off the one that's there); sole is rounded at the edges. But it was cheap!

Re: 3/4 dado plane depth

#3

Re: 3/4 dado plane depth

Don Goodwin

I have an older 3/4" woodie that I bought as a user, but have never cleaned up or tried. It looks like it would cut down about 5/8" with the depth stop fully retracted.

Re: 3/4 dado plane depth

#4

Out of curiosity ...

Derek Cohen (in Perth, Australia)

... Steve, I wonder who uses a 3/4" dado plane?

The reason I ask is that I fit 3/4" wide panels into either a 1/2" dado or sliding dovetail. The 3/4" panel has beauty shoulders to hide the dado.

As a result, I use a 1/2" dado plane. I have the HNT Gordon. Terry does offer a larger, 3/4" version, but it did not seem to me to be a useful size. Am I missing something here?

Regards from Perth

Derek

Re: 3/4 dado plane depth

#5

Re: Out of curiosity ...

Todd Stock

I've kept my #39 in 3/4" for utility shelving where face frames handle the spreading loads, but most recently, the Harvey Ellis-designed Stickley #700 series bookcases...3/4" dado to house the bottom and tenoned stretchers to keep things from moving too much, and (again) face frame and applied pilasters.

Re: 3/4 dado plane depth

#6

Re: Thanks Bill and Don

steve voigt

…I appreciate the info very much!

Re: 3/4 dado plane depth

#7

Re: Out of curiosity ...

steve voigt

Derek, like you, I assumed that 1/2" would be the most useful size. IIRC, I talked to Brian Holcombe about it some months ago, and he also liked 1/2". But recently, I did a little series (on instagram) on making skewed floats for fillister/dado/rabbet planes etc. I was surprised at the interest expressed in dado planes. When I informally polled those people, 3/4" was the most desired size. These are folks who are pretty hardcore, accomplished hand tool users, building period (mostly 18th c.-style) furniture, so I take their opinions seriously.

I think the issue is that you, Brian, and I all tend to like more contemporary designs, where exposed large dados tend to be looked down on, but that is not necessarily the case with older styles of furniture.

If I get around to making them, I'm sure I'd make more than one size, but 3/4" would definitely be in the mix.

Re: 3/4 dado plane depth

#9

Re: I'd love to hear more opinions…

steve voigt

I'd be curious to know if other folks have a most frequently used dado size, if you use them at all. My sample size is fairly small, more opinions are welcomed and helpful…

Re: 3/4 dado plane depth

#10

Re: Out of curiosity ...

David weaver

I don't build much furniture, but it's been my preference to cover dados with mouldings.

I'm about to head to my parent's house, and they have nothing new (I grew up roughly in Warren's territory, and antique furniture is easy to find). It'll be interesting to see if it follows what Steve is saying).

Re: 3/4 dado plane depth

#11

Look to where they are used

Bill Tindall, E.Tn.

If I owned one (too expensive for my occasional use) I would use it to plow a dado across the side of case goods to set the drawer runner into. This dado additionally begins the socket excavation for the dovetailed divider (establishes its location and begins to remove the waste). As it is, I use a router. When I looked into antique planes there was one size that was hard to find.....it may have been 3/4 or 13/16. Post question on SAPFM site. That is where the Period builders are.

These planes are in demand. I talked to a tool dealer that bids on every one that comes up on Ebay , even if it only yields parts.

Re: 3/4 dado plane depth

#12

Re: Out of curiosity ...

steve voigt

Yes, those wide dados are often covered with moldings or the ends are hidden by frames or doors (shelves in an upper cabinet, for example). Dust frames are another common situation for those dados. Sometimes they're 13/16 or 7/7, but that could obviously be covered by the 3/4 size.

Often one sees plans for period furniture in magazines in which the original dados have been replaced by sliding dovetails, stopped dovetails, etc.. Which is fine, but for folks who are using the original construction details, the bigger size seems useful.

One thing you might find of interest is that the hardware is noticeably simpler than on a fillister or plough, even with the screw-adjusted depth stop. The stop itself is very simple and usually solid steel, so no need for sweating on a sole. The nicker also seems simpler to make and mortise in than on a fillister. All in all, not that complicated of a plane.

Re: 3/4 dado plane depth

#13

Good idea Bill, I'll try the SAPFM si


Re: 3/4 dado plane depth

#14

Re: I'd love to hear more opinions…

Warren in Lancaster, PA

Here in Pennsylvania it is rare to use 3/4 as a dimension in traditional work. I can't remember the last time I prepared stock to this dimension. Much more common is 7/8. I guess you could work around a dado plane of a smaller dimension.

Nicholson (1812) says that dado planes are generally about 3/8 inches wide. I have always assumed that he was used to making two cuts for wider dados. For myself I think I would prefer this size to one that locked me into one size like 7/8.

There are five dado planes in the Seaton chest: 3/8 to 7/8 by eighths. Definitely another strategy. Nicholson comments that the more expensive dado planes had brass stops with screws, and Seaton had them. They cost a journeyman at the time almost a day and a half's wages apiece.

Re: 3/4 dado plane depth

#15

Re: Out of curiosity ...

david weaver

Couldn't find anything worth mentioning here.

Re: 3/4 dado plane depth

#16

Re: 3/4 dado plane depth

Kees

My 5/8" Dado plane made by Hields goes 1/2" deep. Of course, no 3/4" but it is another datapoint.

I have never used it for real. But it is a beautifull plane. So I thought, what the heck and post a picture.


img

Re: 3/4 dado plane depth

#17

Re: 3/4 dado plane depth

Hank Knight

That is an attractive plan e, Kees. You need to put it to use.

Re: 3/4 dado plane depth

#18

Re: 3/4 dado plane depth

Kees

In only need a project!

Re: 3/4 dado plane depth

#19

Re: 3/4 dado plane depth

Ron in Sterling, CT

Hi Steve,

Sorry to be late to the party, but I had to dig through my assortment to see what I had. I have two dado planes, both 9 1/2 inches long and missing the two-spurred knicker iron.

The first plane is a 13/16 dado plane made by J E Child (in business in Providence as a plane make between 1850 and 1880). The depth stop will allow a dado depth of 3/4 inch. The iron measures 13/16 wide and 13/16 is stamped on the heel of the plane.

The second plane is a 3/8 dado plane manufactured by Auburn Tool Co, Auburn NY and contains the star in the middle of the identification stamped on the toe of the plane. the depth stop will allow a dado to be made to 1/2 inch depth. 3/8 is also stamped on the toe of this plane.

Hope this helps. By the way, does anyone know where one can obtain the two-spurred knickers?

Ron

Re: 3/4 dado plane depth

#20

Re: I'd love to hear more opinions…

steve voigt

Thanks for the info, Warren, very useful.

Re: 3/4 dado plane depth

#21

Re: 3/4 dado plane depth

steve voigt

Yes, that is a very nice plane, Kees. Thanks for the data point on the depth.

Re: 3/4 dado plane depth

#22

Re: 3/4 dado plane depth

steve voigt

Hi Ron, thanks for the info. Another useful data point.

I am sure no one sells the nickers, but they are not too hard to make. If you are up to heat-treating, a piece of O1 from Victornet, MSC, or anywhere else would suffice.

Re: 3/4 dado plane depth

#23

more thoughts with no opinions

Bill Tindall, E.Tn.

Well, it is certainly true that Period Furniture is typically built with as thick lumber as one can tease out of rough commercial, or custom sawed, 4/4 stock. With care I can usually wind up at 7/8. What that has to do with a dado plane merits further study. The market for dado planes to inlet shelving into something that has shelves is probably miniscule. Even at that I prefer to make the shelf dado 3/4" and notch the 7/8 shelf to fit. The shoulder adds significant stiffness.

I am trying to think where I have used a dado, however made, in the past few years of case goods construction. A dado across a case side to house a runner has already been mentioned. If I blundered into a 3/4" dado plane in perfect useable condition I would consider buying it for this use. I would size the runner to fit the plane and 3/4" would be the perfect start of the drawer divider dovetail socket. I doubt I would afford a new one, but many facing this task would.

Once I plowed a dado that became a dovetail socket in a case bottom. It was probably(?) a 3/4" dado for a 7/8" bottom. And now I have run out of applications. It just isn't a common joint in my recent work.