Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

I'm doing about 100 in reverse today,

Posts

I'm doing about 100 in reverse today,

#1

I'm doing about 100 in reverse today,

Keith Newton

I'm mainly a power-tool user, but have some projects down at my cabin that I'm thinking of doing with just hand tools.

Today I bought a broadax, and ship adz. I've spent the last couple of hours sanding and grinding to get through the pitting, so I can get a sharp edge.

I have been wondering and can't seem to find what the pike on the back end of the adz is used for. I suspect it might be to start a hole to drive a big spike into. The seller had two to choose from, and I chose the one with the flattest blade, though both ends turn up about 1/2" with about 3/8 radius. I found a Plumb mark on it. I think I'll go back tomorrow to buy the other adz with more curve, since it's only $30 and has a longer handle.

I'm sure I'll be making a new handle for the broadax pretty soon. I can see a couple of PP beetle exit holes, plus it was made too close to the pith, which can be detrimental to the strength of most woods. It has M2, or M21 stamped in the head, and does show a line along the bevel where a higher grade of steel was forged in.

Re: I'm doing about 100 in reverse today,

#2

Does the adze look like this?

Bill Houghton, Sebastopol, CA

Does the adze look like the below (image courtesy of eBay)? If so, it's a ship's adze. As I understand it, the adze was used in maintaining ship's decks, and the pin was used to drive nails below the surface, so they wouldn't damage the edge on the adze. The upturned "lips" on the edge were to keep it from making "tracks."


Re: I'm doing about 100 in reverse today,

#3

Yes that is it.

Keith Newton

I think I would have to practice a little bit before I could hit a nail with that little thing. Thanks for the info.

Re: I'm doing about 100 in reverse today,

#4

Practice is everything

Bill Houghton, Sebastopol, CA

I've never seen it, but the folks who write about traditional use of the adze claim that a good practitioner would use his/her boot to stop the cut, and could swing the adze to hit just under the sole of the boot.

Me, I'm kinda fond of my toes. If I ever find myself putting a handle on the adze heads I've acquired and using them, I think I'll take my chances with non-stopped cuts.

In other words, don't try this at home.

Re: I'm doing about 100 in reverse today,

#5

There's a technique to stabilize your swing:

Chuck Nickerson

brace some part of your left arm (if you're right-handed) against your left leg.

For me it's my left elbow against my left thigh.

This really grooves my swing and keeps me from losing control of the adze.

Re: I'm doing about 100 in reverse today,

#6

Well, I've been giving them a test drive

Keith Newton

They will take some practice to get good at using them. I went back to the seller and got the other with more curve. It's a little easier to use than that 5" flatter one. I don't have any green logs around, but had a 6x8" juniper beam from the second log up of a big tree. It had huge knots about every 2', so obviously had a lot of grain change in between them, so I could only get a few strokes with the grain, before I was going against it, even though the easiest cut is across the grain, rather than swinging up and down the axis.

One thing that became apparent right off, was that a very slight bevel on the flat side helps to get the blade to turn up toward the end of the divot. I had to work pretty hard to get all of the rust pitting off that side to keep it straight right up to the edge, but then needed to change it.

I think I'll get the hang of it once I'm using them on some good straight logs. I've got a good old friend that lives in a 100 + year old log house that I was thinking about calling to ask if I could come over and practice on the side of his house. Ha ha