New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Something other than sharpening

Posts

Something other than sharpening

#1

Something other than sharpening

Brian Holcombe

Once the tools are sharp; :D

Good morning! The wall mounted media console is now completed after the final stage, building a set of shelves held in place by moveable shelf pins. I hope that you will check out the post, and I look forward to your comments.

https://brianholcombewoodworker.com/2017/01/26/wall-mounted-media-console-final/

Re: Something other than sharpening

#2

Re: Something other than sharpening

Bill Tindall, E.Tn.

It can't be said that you take the easy way out. Never seen a frame and panel shelf before.

Something to consider- Krenov style shelf brackets. They are pleasant to encounter. In the case illustrated they can be seen through the glass door. In less conspicuous locations I use what you used and in closets, the steel ones.


Re: Something other than sharpening

#3

A near miss for me

Bill Tindall, E.Tn.

When drilling the support holes for the display cabinet I used a section of dowel that the drill went through as a depth stop. In the midst of the 100 or so holes the drill slipped longer as I withdrew it from the hole. I didn't notice. The next hole seemed to be going deeper and I instinctively stopped. Had I continued I would have poked through the front for the frame.

I was using a year-old Ridged battery drill from Home Depot. Don't know if this is a problem to all of them, but these jaws don't grip drills well.

Re: Something other than sharpening

#4

Re: Something other than sharpening

Gary B.

Brian,

Thanks for sharing. In the mortising video, what is in the cup that you keep dipping the mortise chisel in? I couldn't tell by the video.

Bill,

Thanks for posting those shelf clips, you made me smile thinking about one of my first tasks in a professional shop. I had to make maybe 50 of those, but they ended up being dis-similar because of the setting on the bandsaw rip fence (my fault). I got the joy of making them all over again, and learned a big lesson on quality ;)

Re: Something other than sharpening

#5

Re: Something other than sharpening

Brian Holcombe

Nice Bill, I really like those. My wife gave me a raised eyebrow WRT the shelf pins, so I'm quite certain I will be using your Krenov style pegs next go-around.

Good thought on the drill. I marked with a pen, but it is not such a consistent measurement, so I kept a close eye on things to say the least. I have a jacobs chuck for my drill that seems to work pretty well.

Truthfully the only chuck I've ever liked using was one with diamond coated jaws at the machine shop I worked in as a teenager.....but that's a bit like only enjoying the drive that a Maserati offers...

Re: Something other than sharpening

#6

Re: Something other than sharpening

Brian Holcombe

Thanks Gary, that is my handy oil pot...aka a cheating device for mortising. Makes the work much easier.

Re: Something other than sharpening

#7

Aids for drilling to a set depth

Bill Tindall, E.Tn.

1. For a bunch like the shelf bracket holes installing a dowel stop on the drill is quick and secure if the chuck isn't crummy. I cut the dowel to approximate length, drill the hole through the center and drive the drill bit through. Small depth adjustments are made by positioning the drill bit in the chuck.

2. For a few holes, I cut a thin (1/8") strip of masking tape and wrap it around the drill bit with the bit centered in the tape. The bottom of the wrap is at the desired hole depth. The result is a "flag" that extends from the bit. As the drill drills bits of wood gather at the entry hole. When the depth indicating flag reaches the wood surface the bits are swept away. Works great and lots of shops use this technique.

Re: Something other than sharpening

#8

Re: Aids for drilling to a set depth

Brian Holcombe

Thanks Bill, those are great suggestions, I will put them to use.

Re: Something other than sharpening

#9

Monitor the opening for the wires.

Gary Smyth

Wire bundles seem to grow. In my instance for a media cabinet I originally ran amplifier, tuner, equalizer, turntable, air fan, speaker wire (each numbered on its end). Some were heavier gauge and different lengths than the others. Over time to hide wires I added telephone charger, fax, printer cables off of a power strip located inside the cabinet. Then came the lighting, patch panel, wireless connections and cable router. What with the transformers for some of the electronics the back of the cabinet filled. The opening meant to hide the wires was too small. Part of the problem was that some cable lengths had to be "wire managed" and hung on the sides or rear or coiled. As long as there was no repair or new stuff added it worked. However, when something was replaced to pull the old plug/cable and put in new, the opening was progressively too small and the cables tangled. I was working out of the opening a bit larger than yours in the bottom third of the cabinet and had a full fifteen inches from the back of the cabinet to the rear of the original audio components, so I thought there was plenty of space. I was wrong. When I eventually build the new cabinet there will be an opening the full width of the compartment, and it will be wide enough to allow a transformer to slide nicely in or out with all of the other remaining wires connected. Let us know what your experience turns out to be.

Re: Something other than sharpening

#10

Re: Aids for drilling to a set depth

Bill Houghton, Sebastopol, CA

I use the tape, but I don't bother to cut it skinny; full width works fine.

Re: Something other than sharpening

#12

Already know what I'm up against

Brian Holcombe

...because I own much of the same equipment and fit it into a smaller opening. :D

This is a media cabinet, that is true, but there are two spaces 15" deep by 21" wide by 7-8" tall that are being fed by a 3.5" square hole and 1" clear space behind the shelf. So I'm not sure that even enough variety of electronics could possibly build a bundle too large for that, given the available space for electronics.