New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Ruler Trick with Spokeshave Blade

Posts

Ruler Trick with Spokeshave Blade

#1

Ruler Trick with Spokeshave Blade

James Blandford-Baker

Do any of you have ideas for using the ruler trick (aka 'The Charlesworth'!) with the short blades of the Boggs L-N spokeshaves? They are a bit tricky to handle and of course the angle of the polished bit on the back is steeper (since nearer to the ruler) than with a standard plane blade, unless one could find a way of artificially lengthening the blade while doing the polishing.

Thanks!

James

Re: Ruler Trick with Spokeshave Blade

#2

Someone remind me why......

Bill Tindall, E.Tn.

...back beveling the blade of anything we use is a good idea? Is this a suggestion that has not stood the test of time....or is it perceived to be a good idea, and why?

Re: Ruler Trick with Spokeshave Blade

#3

Re: Ruler Trick with Spokeshave Blade

Wiley Horne--So. Calif.

Hello James,

To work the back of that blade (and other shave blades), I place the lower 1/2" or so of the blade on the long edge of a finish stone, and work it laterally along the stone. One finger is on the bevel of the blade (which is facing upward of course)--this keeps positive pressure on the back, right to the blade edge. The other hand stabilizes the blade. Using both hands to hold the blade firmly onto the stone, just work it up and back along the stone edge. I see no need to actually angle the blade back, as in the ruler trick, since the finger pressure on the bevel is sufficient to make positive contact of the back, right to the blade edge.

Lateral (90-degree) and 45-degree sharpening along the edge of the stone also works well for the bevel side of a short blade!

There are other ways to do this job of course, so I am not holding out my method as The Way :) .

Wiley

Re: Ruler Trick with Spokeshave Blade

#4

Re: Ruler Trick with Spokeshave Blade

Derek Cohen (in Perth, Australia)

Do any of you have ideas for using the ruler trick (aka 'The Charlesworth'!) with the short blades of the Boggs L-N spokeshaves? They are a bit tricky to handle and of course the angle of the polished bit on the back is steeper (since nearer to the ruler) than with a standard plane blade, unless one could find a way of artificially lengthening the blade while doing the polishing.

Hi James

Wiley gave excellent advice. I do essentially the same as he - the 1/2" behind the bevel flat on the finishing stone (only) and wiped side-to-side to remove any wear bevel. I repeat on green compound-on-hardwood.

The bevel is hollow ground. This is the trickier bit since the blade is narrow. Still, the hollow is the key to sharpening. The better you do this, the easier is the honing. "Better" in my case is a hollow that is as close to the edge of the bevel, and as straight, as possible. This leaves the least amount of steel to abrade.

Once done, the hollow acts as a guide for freehand sharpening. Again, I do this in a side-to-side direction (this offers up the most registration and stability), with some 45 degree moves as well. Ideally, I want to raise a wire edge with a 1000 grit in 2 strokes. This will be followed by 6000 and 13000 (I use Sigma).

Regards from Perth

Derek

Re: Ruler Trick with Spokeshave Blade

#5

Re: Ruler Trick with Spokeshave Blade

William Duffield

Without getting into trigonometry formulae, You want to liftthe angle of the blade a very small amount. If you can't do this by moving the ruler farther from the edge of the blade, you can do it by using a thinner ruler, closer to the edge. Your ruler doesn't even need and graduations etched into it. So, just pick a thinner feeler gauge for your spoke shave blades. Consistency in angle and number of strokes is more important than the measured value of the back bevel angle.

Re: Ruler Trick with Spokeshave Blade

#6

Re: Ruler Trick with Spokeshave Blade

Wiley Horne--So. Calif.

Right! A business card ought to do it.

Wiley

Re: Ruler Trick with Spokeshave Blade

#7

Re: Ruler Trick with Spokeshave Blade

TomD

It's tough to get even pressure, if you want uneven pressure which is the idea of the trick, just keep pressure on the bevel area. Basically the same deal as when sharpening a bevel you keep your pressure as squared up over that area as possible. Do that when sharpening the back and you will acheive the same result as the ruler trick. You won't possibly have exactly as much control, but it isn't an area where that maters too much.

Re: Ruler Trick with Spokeshave Blade

#8

Re: Someone remind me why......

TomD

There are a lot of reasons why back beveling is both traditional and useful.

The ruler trick, however, is mostly a means of ensuring that beginers, and others who want to do it, get a truly polished back of the blade edge, which is a critical step. On some tools, particularly by hand, this a a very difficult undertaking because there is such a large area to work. One some tools it will stick or hydroplane. I think many have been through the situation where the whole back is nice and flat except some fragment of the edge but that means endless work on it to get the whole surface referenced. Some will quit when it all looks good and still not get a good edge. With the ruler trick it allows the micro bevel to be formed and to be in good control, and you may or not choose to hit it again every sharpening. It avoids the risk of rounding. In that sense it is different from at least convex back bevels, it is also a very slight variation, not say 5 degrees or more.

I don't use it as I long since got past this point, but I can see the advantage. Plus it could probably work with breakers.

Re: Ruler Trick with Spokeshave Blade

#9

Re: Ruler Trick with Spokeshave Blade

TomD

Just tape one end of the stone, and rest the end of the blade on that if you don't want a fingers method.

Re: Ruler Trick with Spokeshave Blade

#10

Re: Ruler Trick with Spokeshave Blade

Wiley Horne--So. Calif.

Agree. That's precisely what I said up above.

Wiley

Re: Ruler Trick with Spokeshave Blade

#11

Good idea


Re: Ruler Trick with Spokeshave Blade

#12

Re: Ruler Trick with Spokeshave Blade

TomD

I didn't see anything about tape.

Scotch tape is 1 thou, business cards are 13-14. Not really sure which is better. Started to think that over the length of a 9 inch plane blade on a ruler, 13-14 might be more than was required on a short spokeshave blade, there is a lot of different tape. But I don't use the trick, so it would be something one could play with if one wanted to, in which case starting low might be better.