New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Live Edge Tsuridana

Posts

Re: Live Edge Tsuridana

#2

Re: Live Edge Tsuridana

AZ in Colorado Springs

Brian, how did you mark the overall thickness of the slab? Did you scribe around the edges before cutting the rabbet along the front and ends? Or scribe the thickness later, using tow settings? Or use some different technique? Starting with 10/4, what was the final thickness?

Re: Live Edge Tsuridana

#3

Re: Live Edge Tsuridana

Brian Holcombe

Thanks AZ, what I ended up doing was scribing the back of the slab, then scribing the front taking into account the change in dimension.

As a double check I used my winding sticks and a double square to measure against my bench to ensure that I was accurate. I also checked the face for wind when all was said and done.. I find it very hard to scribe accurate dimensions on a live edge slab at some junctures (depends on how the edge goes), so I like to double check.

The finished dimension on the front edge is 1.5"~ The current trend is for very thick slabs, but personally I prefer the appearance of 8/4 thicknessed to 1.5" or 1.75". Once they get to 2" or 2.25" they appear very heavy, IMO.

Re: Live Edge Tsuridana

#4

Second question

AZ in Colorado Springs

What do you use for winding sticks? Looks like 1/2" x 1" bar stock?

Re: Live Edge Tsuridana

#5

Re: Second question

Brian Holcombe

I only use those for large slabs or panels, they're 3/8" x 1.5" x 36" precision ground steel.

Re: Live Edge Tsuridana

#6

Re: Second question

AZ in Colorado Springs

Thanks

Re: Live Edge Tsuridana

#7

Re: Second question

TomD

And this is one wooden tool application where the wood is both more accurate and a better choice since it produces less glare and can easily be contrasting colours. More accurate if you plane the matching set they should be a lot closer than precision ground, not that it probably maters. So

Re: Live Edge Tsuridana

#8

Re: Second question

William Duffield

Extruded Aluminum angle stock works well, is light weight, inexpensive, durable, and accurate enough for most woodworking.

Re: Live Edge Tsuridana

#9

Or, if you are a garage sale shopper

Bill Houghton, Sebastopol, CA

watch for cheap aluminum levels. My two winding sticks cost $2 - $1 each - for levels that I'd never trust to level anything; but they work fine for winding sticks.

Re: Live Edge Tsuridana

#10

Re: Second question

AZ in Colorado Springs

Are you suggesting that the winding sticks need to be the same height? I'm thinking of your comment about planing them together.

Seems to me that's less critical than being completely straight.

I realize you wouldn't want one 1/2" or 1" taller than the other, but it seems that is less of an issue than being straight. Steel or aluminum won't move over time like wood.

Re: Live Edge Tsuridana

#11

Re: Second question

William Duffield

Wooden winding sticks move, and can move significantly. It is much, much simpler to adjust them to straight and parallel (tune them) if you can joint the pair together (match plane them).

Re: Live Edge Tsuridana

#12

Re: Or, if you are a garage sale shopper

William Duffield

It doesn't hurt them to use a pair of levels you do trust as winding sticks, and you don't waste your time and gasoline futilely haunting garage sales for WalMart relics. :D

Re: Live Edge Tsuridana

#13

True

Bill Houghton, Sebastopol, CA

I don't know how many folks have more than one, say, two-foot level.

Re: Live Edge Tsuridana

#14

Re: True

William Duffield

Well! I have two two-foot levels, and two four-foot levels, and I am NOT a collector.

While there's nothing wrong with salvaging something that can still be put to use, even if it can no longer serve its original purpose, most of us who could make good use of winding sticks should also have use for a matched pair of functioning levels.