New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Making a card scraper?

Posts

Making a card scraper?

#1

Making a card scraper?

Joe in a Cleveland suburb

I have several old kinda rusty card scrapers somebody gave me a long time ago. They are similar to the Sandvik scrapers. I have the need for a rounded scraper or two to clean/smooth the insides of round'ish profiles. I thought maybe I could use these old ones to try and make one or two of the profile I need. Pretty simple round profiles - like the bowl of a spoon.

How would I go about cutting the old scraper? Just a hack saw? Clean up with a file and try not to round it over? Can I clean it up with a slow speed grinder and white wheel or will that over heat the metal?

I do a decent job of putting a bur on regular straight scrapers, so I guess that won't be a problem. Just wonder about ways of cutting and profiling old scrapers.

Thanks for any suggestions and/or tips.

Re: Making a card scraper?

#2

Re: Making a card scraper?

TomD

It depends on how hard they are. If they cut with a hacksaw, they are probably fairly saft, but at least you are guaranteed they won't loose any hardness to heat.

If you have a dremel tool, those little abrasive cut off wheels will cut any metal, and they have a very fine kerf, which means less heat. They are very fragile, though, and blow up easily. The particles are not normally dangerous so long as you wear good eye protection.

Heat is only really a problem if you don't use the right technique, you want to make clean cuts that don't clog and in the case of a curve you might try outlining it with some straight cut, and nibbling off the corners, rather than trying to follow a line.

You grinder should be fine, just be sure to have clean stones, and dip the scraper into water so that a film remains. Grind until the film disappears an re-dip, repeat.

Re: Making a card scraper?

#3

Re: Making a card scraper?

Clifton C

Joe,

I had the need for some small scrapers, but didn't want to cut up my "broken in" scrapers. I bought a Bahco scraper from Lee Valley. The specs say Rc48-52, Not sure exactly what that means but I had no problem cutting it with a hacksaw. I covered the scraper with masking tape, drew out the profiles and cut close. Then "lapped" off the ragged hacksaw burr with some 320 to make it easier to slide on the grinder platform. A light touch on the grinder to fair in the curves then lapped on some 600 grit resulted in some nice little scrapers.

cc


Re: Making a card scraper?

#4

Re: Making a card scraper?

Bruce, a MN Galoot

Use a Dremel with a cut-off wheel as TomD suggest, easy peasy. I've cut up an old handsaw plate that I bought just for that purpose. Clean up with a file and you can have special purpose scrapers in no time flat. I must have a dozen or so.

Re: Making a card scraper?

#5

Re: Making a card scraper?

Joe in a Cleveland suburb

Thanks guys.

I have a Dremel and rarely use it.

What do you mean by cut-off wheel? Are those those super thin brittle disks that break when you look at them?

Thank you.

Re: Making a card scraper?

#6

Re: Cut-off wheels

TomD

Yeah, those be they. There are two types, one is glass reinforced, and they are better, but either will do. Back when I was learning tube work for bicycle building I had a pal who was into the chopper thing, and we were working on various things to cope tubes. He mentioned he was coping the tubes for his frame with a dremel and those wheels. Sounded preposterous but I tried it, and they zipped through the curves and 1/8" walls with ease. They can break in the cut, but they almost always break when I put the tool down on a cluttered bench, anything that touches them breaks them.


Another place I would never have though of using them is if you know what a bow looks like you will know there is a deep cut-out where the arrow goes on the shelf. On a modern bow that can be something like Brazilian rosewood, and heavy glass or phenolic composites. Tough to cut in any direction without tear-out, and the action glass is a splintery non-crosslinked material that is easily damaged. I was talking to this famous bowyer and what was his favourite tool? Dremel with a the carbide freehand cutter!