New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Drilling a saw plate question

Posts

Drilling a saw plate question

#1

Drilling a saw plate question

Bill Tindall, E.Tn.

I may have to enlarge the hole in the plate of an old saw in order to accommodate the size saw nut I can buy. Directions various places call for drilling the hardened steel with a carbide drill, which I don't own. Question:

Would it work to simply heat (more or less?) the spot with a micro-sized torch, then cool this spot by some means? The idea is to anneal the metal so that it could be drilled with any metal drill bit. If this idea has merit how much to heat and how to cool to result in a softened spot?

Saw kits are only $50-60. finished saws are 4-5 times this price. How much time does it take to convert a kit to a serviceable saw, not presentation grade? It looks straightforward to someone that has never done it. I tend to be optimistic to a fault. :)

Re: Drilling a saw plate question

#2

Re: Drilling a saw plate question

Mike Jurnigan in Zuni

Bill,

If you have a Dremel type tool why not enlarge the hole with a burr or a stone?

Mike

Re: Drilling a saw plate question

#3

That is what I'd try too...

John in NM

Or if the hole needed to be much bigger, perhaps I'd re-grind a cobalt bit to do the job (I like a grind similar to a brad point spur bit for sheet metal).

Re: Drilling a saw plate question

#4

Re: That is what I'd try too...

Walter Barbier

I tried a Milwaukee Cobalt Red Helix bit on an old Disston saw that I picked up. Don't know the age of the saw but it was pretty well sharpened to a nub. The bit worked fine. Used a low speed on the drill and it cur right through, left a clean hole.

Re: Drilling a saw plate question

#5

Re: Drilling a saw plate question

Warren in Lancaster, PA

Saw plates are deliberately tempered enough that we can file them. You ought to be able to enlarge the hole with a file without more tempering. I have also drilled saw plates with twist bits, which are considerably harder.

Re: Drilling a saw plate question

#6

Re: Drilling a saw plate question

Derek Cohen (in Perth, Australia)

Hi Bill

Either enlarge the existing holes with a round chainsaw file, or drill out with a carbide drill bit. An example of the latter is below ..


Regards from Perth

Derek

Re: Drilling a saw plate question

#7

I like the file idea

Bill Tindall, E.Tn.

The saw has one missing screw which makes the handle a bit wiggly, and hence annoying, but I have endured it for several years.

There are some things where proceeding slowly ensures success. I can drill out the wood to the correct diameter, remount the handle and use the wood hole as a filing guide. Sounds like a plan.

I do have cobalt drills but I have experienced

catching" issues when enlarging holes in sheet metal with twist bits.

Re: Drilling a saw plate question

#8

Re: I like the file idea

TomD

If you clamp the saw plate so it can't move you should be able to drill it, at least you won't need to have your hands on it, but it will drill. Mount the saw so if it does catch the teeth are trailing. Never underestimate the awesome force of a drill press.

Carbide bits in small sizes are very cheap and available on ebay, though you don't need them.

Your idea with the torch should work fine, but refinements to that strategy are to use your torch to heat a rod red hot, or at least 900 degrees, then force that against the plate, this precisely centers the heat. For small hole an approach used would be to put a nail or rod in a drill press and spin it will quill down force, this friction aneals the area to be drilled, though where there is already a hole, you would need a pilot. You can use the hot rod without the.

Probably the correct tool for the project is a chucking reamer, in small sized they are pretty cheap, they are at best able to enlarge about 1/16", though the actual cut depends on size. They are for fitting holes more than blowing them out. But they can do either. The come in 1thou increments, at places that have every tool. You can get major fractions in many places, and they often sell a 1 thou up size for slip fits. Try ebay, or victornet.com Or any of the large ind. supplies. They are quite useful for wood also.

http://www.victornet.com/subdepartments/Chucking-Reamers-to-3/8/1780.html

Re: Drilling a saw plate question

#9

Re: Drilling a saw plate question

Paul in NJ

Hi Bill,

How much time does it take to convert a kit to a serviceable saw, not presentation grade?

With a pre-punched saw plate, it takes me roughly 30 minutes for a rip and probably twice that for a cross cut. Finer tooth saws with more teeth take longer. Add 20 minutes to set the teeth. I am not a pro so I go slowly.

By far the most time spent is the handle. I recommend doing the slot for the plate, drilling the holes, and fitting the plate to the handle before investing time shaping.

Paul Dzioba

Re: Drilling a saw plate question

#10

Re: Drilling a saw plate question

Bill Tindall, E.Tn.

thank you