New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

update on bench grinder

Posts

update on bench grinder

#1

update on bench grinder

Bruce Mack

I succumbed to wheel envy. I could not abide the residual slight vibration from the aluminum oxide wheels and I did not like wearing goggles as they made it difficult to see the bevel/grind (I normally wear graduated bifocals). I got a 60 grit CBN wheel from Joel at TFWW, removed the DeWalt tool rest, and got a Veritas rest which is more easily adjustable. As GolfSteve noted, the new rest has flex under pressure but the very light touch needed with the CBN wheel eliminates any concern for me. The set-up has no vibration, though the usual machinery noise. I wear my regular eyeglasses as no fear of the wheel breaking apart.

Re: update on bench grinder

#2

Re: update on bench grinder

Denny

Bruce, is there a reason you can't wear safety goggles over your bifocals? I do it all the time.

Re: update on bench grinder

#3

Re: update on bench grinder

Bruce Mack

Denny, maybe I'm a klutz but the goggles tend to push my eyeglasses against my face, leading to smudges from the eyebrows or lashes.

Re: update on bench grinder

#4

Re: update on bench grinder

Denny

I guess I'm a klutz too, I have to clean my glasses all day long. But I'd rather go through lots of kleenex to clean my glasses if it means I can still use safety goggles. I would urge you to be cautious around ANY power tools.

Re: update on bench grinder

#5

Re: update on bench grinder

Bruce Mack

Good point.

Re: update on bench grinder

#6

Ditto on the caution


Re: update on bench grinder

#7

my glasses are safety glasses

Bill Tindall, E.Tn.

The difference between "ordinary" glasses and safety glasses is that the safety "glass" is polycarbonate instead of acrylic and the frame is possibly a bit different. Neither factor is noticeable to me. Given the greater toughness of polycarbonate I would be asking for lens made from this material in any case.

In some situations of my part time work I am required to wear safety glasses. I experienced no difference wearing them vs "street" glasses. Since I can buy the safety glasses cheaper it became a no brainer to wear safety glasses for all occasions.

Re: update on bench grinder

#8

Re: update on bench grinder

Bruce, a MN Galoot

I would recommend a dust mask, too. On a couple occasions, polishing aluminum and brass, my lungs felt and acted as if I had pneumonia. Very fine metal particles get in and they don't leave and they can cause great damage.

Re: update on bench grinder

#9

Re: update on bench grinder

don stephan

When grinding I wear goggles or full faceshield (if turning on the lathe) to minimize the chance of pitting my expensive eyeglass lenses.

Re: update on bench grinder

#10

Re: update on bench grinder

jerry roberts

If you are interested...Sometimes I shoot at the local range and are required to use safety glasses but I also wear eyeglasses. I was advised to get shooting goggles by the name of "coveralls" that can be worn over regular eyeglasses. They save a lot of aggravation for me.

Re: update on bench grinder

#11

Re: update on bench grinder

Bruce Mack

Thanks. I've ordered them. I'm not cavalier about my eyes, but felt the polycarbonate rx. lenses would protect them from the fine metal particles produced when grinding. I have used protective goggles without prescriptive correction for other machining as most, like feeding the tablesaw, don't require visual finesse during the process (after careful set-up). These cover lenses should permit me to wear my corrective lenses at all times.

Re: update on bench grinder

#12

Re: update on bench grinder

TomD

I think if you are worried about wheel explosion you need something a lot more than safety glasses and that goes for metal particles also. Unless you will never need an MRI, you really need to take care. These new wheels are probably a good investment in health and safety in a small shop.

You can watch safety videos online for grinding, if you have the stomach for it. You need to be ready for an attack by an axe. I had a wheel blow up on me a few weeks back. It was one of those porous wheels for a grinder, high rpm, and it wore down, and blew up. I think I had a face shield on. Hurt a bit, no biggie, but to the face, wow! That would be something, and that was nothing compared to the weight of a wheel. I have had a variety of bowls go wizzing past. Some just spin out on the ways, others go by like a rocket, depends whether they catch on anything. Those are low RPM and light weight, but scary.

I learned to grind from a raffan video back in the 80s, and he stood to the side which allow you to see the tool contact point, and also protects you from what happens when the debris cuts loose.

A common path for metal fragments to the eye is a bounce off the cheek bone, so I guess some people might be more susceptible than others depending on the angles.