New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Kezurou-Kai Prep

Posts

Re: Kezurou-Kai Prep

#2

Re: Kezurou-Kai Prep

Wiley Horne--So. Calif.

Hello Brian,

This will be a great learning experience for us all!

I hope you (or someone) will take lots of photos of tools, techniques, shavings and so on.

I am curious whether you and the others will be using double irons or single irons for this specialized purpose, with straight-grained wood tailored to the specific purpose. Also, will the participants be using natural stones or man-made (and if so, which). And what type of scopes do the Japanese participants use to examine their edges--I believe So told me they use a particular scope with 100x magnification. What blade widths?

Much thanks for sharing this!

Wiley

Re: Kezurou-Kai Prep

#3

Re: Kezurou-Kai Prep

Brian Holcombe

I'll likely do a write up on it. I suspect it will be mostly single irons and natural stones.

It'll certainly be interesting, I know last year's winner made his own iron and chopped his own dai.

So told me that many of the guys use Peak 100x or 200x microscopes. I do not use a microscope but may well do so before next year.

Re: Kezurou-Kai Prep

#4

Re: Kezurou-Kai Prep

Wiley Horne--So. Calif.

Brian,

Good luck! Takes guts to go against the best.

Wiley

Re: Kezurou-Kai Prep

#5

Re: Kezurou-Kai Prep

TomD

The thinnest practical shaving I have taken is around 4 tens which is apparently 10.2 microns. I didn't really have the ability to confidently measure such shavings but certainly in that area. That is relatively easy to do, but getting level and even shavings over the length of a board is another mater. 4 tens is useful for polishing shoji and such. A 2 micron shaving would be a quantum difference for sure. I have to say I was never able to prep a plane with a scraper plane to that level, and always fell back on sanding the soles on a flat surface. The first plane I had that did that was not fancy it was a scraper plane blade in an american white oak dai I made that was loose enough to hand adjust the blade. But super sharp blade (actually just king 8K stone) and flat sole so one can get under the shaving, and it was easy.

Re: Kezurou-Kai Prep

#6

Re: Kezurou-Kai Prep

Brian Holcombe

If I win then I went to compete....if I lose then I went to have fun. :D Given the competition there is a good chance that I'm going to have fun.

Re: Kezurou-Kai Prep

#7

Re: Kezurou-Kai Prep

Brian Holcombe

I sand the sole as well, then scrape hollows.

If you are getting 10 micron shavings than whatever you are doing is working well!

Re: Kezurou-Kai Prep

#8

Re: Kezurou-Kai Prep

TomD

I am getting that if it is .0004". Could be a math problem though. Takes 3 to 4 folds to register on a high quality caliper. I'm not a machinist, but I have all that stuff and know the basics of measuring. Just tough to say with pine, I don't think it compresses during measurement. Plus other factors are the look of the shavings and the optical properties of the surface, reading lightbulbs and that kind of jazz. I mostly hand sharpen, but was using a blade guide at the time of my interest in this stuff. I gather the guys who are serious use guides and optics in sharpening.

Re: Kezurou-Kai Prep

#9

Stanley

David Charlesworth

My tuned up Stanley 5 1/2 ,with Hock blade, will produce shavings of around 12 microns, but from a relatively narrow edge. Say 3/4".

Have not tried 2" edge!

Good Luck.

David

Re: Kezurou-Kai Prep

#10

Re: Kezurou-Kai Prep

Brian Holcombe

I have a guide specifically made for this and basically just use it to make the last few passes or so and make a tiny microbevel. I don't know if the serious guys are using this but would have to assume so because it makes extreme flatness across the full bevel less of an issue. I say less because I also assume that applying this last bevel evenly means have consistent wear on the bevel against the stone.

Re: Kezurou-Kai Prep

#11

Re: Stanley

Brian Holcombe

That's pretty good!

I've been using my 7 plane as a sort of 'zamboni' to clean up the edge after a few passes, if a ripple shows up.

2" does add a fair amount of difficulty, I think it's worth the novelty of trying and makes my head spin when I see those guys using the really wide Ookannas to pull a full width shaving off of a big piece of timber.

Re: Kezurou-Kai Prep

#12

Re: Stanley

David Charlesworth

Brian,

I'm sure you will have a great time.

I have to say, I would have to see the 2 micron shavings before believing. However the wood species and condition must have a great effect.

Best wishes,

David

Re: Kezurou-Kai Prep

#14

Re: Stanley

TomD

So that record is like 1.2 tens, which makes mine like running the 100m in 30 seconds. So I think that is in the realm of possibility for anyone who wants to try, even when they are an extreme newbie. 4 tens is like half a working shaving for a lot of people in the 1 thou range. My shaving folded in 3 was 1 thou with the needle on the edge of the 1 thou, which looked like 1.2 thou to me.