New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Charging a cast iron plate with diamonds

Posts

Charging a cast iron plate with diamonds

#1

Charging a cast iron plate with diamonds

Bill Tindall, E.Tn.

Diamond charged on cast iron and lubed with olive oil has been used for centuries for polishing gems, including diamonds.

I was told by a gem cutter to add the diamond paste (oil based) to the cast iron, spritz with olive oil, smear around by some means and embed by rubbing with a curved inexpensive stone like sapphire. I was to receive an appropriate sapphire but never got it. I think any stone with a radius surface would do acceptably, but I don't have one.

What I in fact do:

Squirt about 1 cm of paste onto the 12" long plate. Most beginners use way too much paste. I actually distribute it about the plate for a total of about 1 cm or less. I add some drops of WD40, wrap my index finger in a condom made from a piece of plastic grocery bag (I am unsure what those in CA will be able to do), and smear the paste about the plate.

At this point it would be ideal to then rub a stone on the plate to embed the diamond. I don't have one so I rub what I need to sharpen. From time to time I return the liquid, that no doubt contains some diamond, that gathers on the metal back to the plate.

When I am done sharpening I wipe the plate with a paper towel and return it to a plastic bag. I do not recharge every time I use it. I do lube with WD40 as its viscosity is just right.

Re: Charging a cast iron plate with diamonds

#2

Thanks, Bill


Re: Charging a cast iron plate with diamonds

#3

If you want that sapphire...

John in NM

Google synthetic sapphire boule. There are a number of suppliers for these, they are typically a half cylinder about two inches long and last time I bought one they cost about $10. Morion Co. was one I bought from at the gem show in Tucson. They have a website but I find it a bit confusing. You could also try Graves Co in Florida, in addition to manufacturing faceting equipment and laps they used to sell diamond grit and inexpensive rough.

Re: Charging a cast iron plate with diamonds

#4

Thank you.


Re: Charging a cast iron plate with diamonds

#5

not cheap

Bill Tindall, E.Tn.

That gave me an idea. The sapphire seems to cost $25 and up. But I am thinking a ceramic rod might do or a carbide rod and I have both.

Then another thought crossed my mind. Maybe I would have less diamond embedded (contaminating) in the steel if it was better embedded in the cast iron.

Re: Charging a cast iron plate with diamonds

#6

Re: not cheap

John in NM

Yeah, they've gone up since I last bought any....

Ceramic rod will work fine too, probably carbide also.

Re: Charging a cast iron plate with diamonds

#7

Re: Charging a cast iron plate with diamonds

TomD

I not only don't recharge every time I use it, I don't recharge every year. So far I am several years into a leather strop I charged once or twice and didn't use much on it to start with. They are diamonds, they don't seem to break down.

Re: Charging a cast iron plate with diamonds

#8

Re: Charging a cast iron plate with diamonds

Bruce, a MN Galoot

Bill, do you jump right from 15 microns to 3 microns for a finishing hone?

Re: Charging a cast iron plate with diamonds

#9

yes but

Bill Tindall, E.Tn.

One can jump from 15 to 1 and the 1 will promptly remove 15 scratches as well as get contaminated with 15 particles carried over from embedding in the chisel.

Re: Charging a cast iron plate with diamonds

#10

Re: yes but

Hank Knight

Bill, doesn't that happen each time you transition from a coarse grain to a finer one? How do you prevent it? Can you prevent it? As a practical matter, does it matter?

Re: Charging a cast iron plate with diamonds

#11

my opinion

Bill Tindall, E.Tn.

Bill, doesn't that happen each time you transition from a coarse grain to a finer one?......I believe so

How do you prevent it? I don't believe you can

Can you prevent it? Not to my knowledge

As a practical matter, does it matter? I believe so

Hence. I either do the first abrasion off the grinder with a fine fixed diamond plate then 1 micron loose diamond

Or

I am experimenting with 15 micron loose diamond after the grinder and then strop on leather with green stuff.

Re: Charging a cast iron plate with diamonds

#12

Re: my opinion

Hank Knight

Thanks, Bill. I'd like to know what you decide works best for you. I'm setting up for loose diamonds, actually diamond paste on cast iron. I resurrected my Tormek for the rough grind. My plan is to start with the coarse wheel on the Tormek, then refine after using the "stone grader" to reduce the wheel's grit, follow with 3 micron paste on cast iron and finish with .5 micron on leather. I' a little apprehensive about the jump from the fine Tormek wheel to 3 micron diamonds, but I think it will be O.K. With this progression I only risk contaminating my strop with 3 micron diamonds. I'd rather replace a strop occasionally than the cast iron plate.