New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Fitting drawers

Posts

Fitting drawers

#1

Fitting drawers

Bill Tindall, E.Tn.

After 2 weeks vacation it is nice to be back in the shop. I'm fitting the drawers for the bed side chest of drawers. The shop humidity was high when I returned and now is the time to fit. If they fit now, they always will fit. And because the humidity is high I fit them tight.


I like fitting drawers. The planing is predictable because I have oriented the drawer grain to provide for favorable planing during fitting. It is satisfying to have a bindy drawer, remove a few shavings and then have it slip effortlessly into the opening. When fit properly the drawer closes without binding, even when pushed from one corner. In fact that is my target for fitting. I want to be able to smoothly close the drawer by pushing on one corner.



I study drawers every time I get in an antique shop. I have concluded from these studies that a total gap of slightly less than 1/16" is optimum for the length. The ideal top gap will depend on the humidity when the fitting is performed. In this case I again targeted a bit less than 1/16" .

The quarter sawed poplar was salvaged from a yard tree cut in my daughter's neighborhood in SC. I roughed out the quartered pieces with a chain saw then later sawed the blanks on a band saw and finished drying in the hot car sitting in the sun.

Re: Fitting drawers

#2

Re: Fitting drawers

TomD

Beauty.

Re: Fitting drawers

#3

Re: Fitting drawers

Brian Holcombe

Nice work Bill. How do you fit the backs of your drawers? I'm curious if your procedure is similar to my own.

Re: Fitting drawers

#4

summary of procedure

Bill Tindall, E.Tn.

I have learned to spare no effort getting the case square and the sides flat( which hints at the fact that this goal is not always reached. But I'm getting better). I loosely fit the drawer front and back to their respective positions in the front of the case. Ideally the gap at this point is some less than the final fitted gap around the drawers. Then I assemble the drawer and insert it into its opening and wedge it in place with thin tapered wedges or sometimes just a piece of stiff plastic if the gap is small. If one is sloppy with glue it would be prudent to ad wax paper to the procedure so the drawer is not glued in place from squeeze out. I rarely add this step.

When the glue is cured I remove the drawer and plane it to fit. With a block plane or spoke shave I plane a concave edge on the top of the back so that there is no risk of the back top edge dragging on the drawer dividers. It will be concave by about 1/32".

Lastly I insert the bottom and add a screw or two at the back to hold it in place.

Alternatively the top edge of the back can be mowed off some so that it sits below the drawer sides. In the Headley shop one worker did it this way and the other planed a concave edge. Clearly there is no "right" way.

Re: Fitting drawers

#5

Re: summary of procedure

Brian Holcombe

Thanks Bill, that's practically identical to my procedure as well, so I'm glad to be in good company.

I certainly appreciate your comment about case squareness, I used to aim for a slight taper 1/16"~ front to back but I'm doing away with that as I'm finding it more of a nuisance than an aid.

I notice a lot of people will only show how their drawers work by lifting and pushing from the center to make for an ultra smooth ride, so I'm glad to see your comment about pushing from the corners, which is particularly tough to get perfect on wide drawers.

Re: Fitting drawers

#6

I suspect one departure....

Bill Tindall, E.Tn.

When I am making a drawer for a utilitarian piece like a place to put your socks, I finish the drawers with shellac. Dilute Zinser, scuff sand, recoat. It keeps the wood bright, promotes ease of sliding, and repels whatever might get spilled over the ages.

Re: Fitting drawers

#7

Re: I suspect one departure....

Brian Holcombe

I've used oil finish in the past but will be using shellac on this one. I dont need to dilute it, as I use flakes and alcohol and I make it with a pretty light cut for ease of wiping.

Re: Fitting drawers

#8

Quicker than wiping

Bill Tindall, E.Tn.

The typical foam "brush" disintegrates in alcohol. However, the brushes with the yellow removable handle from Woodworker Supply hold up well enough to be useful. They provide a dandy way to apply shellac. With the 3" variety two passes down a drawer and done. I apply shellac, about 1.5 cut. After drying I scuff sand with 320 or 360 grit, then recoat. Then wax if it is a drawer side or case interior. The wax is hard Carnauba dissolved in Xylene.

Shellac and a hard wax will result in a drawer that acts like it is on ball bearings.

Oil can result in a stinky interior space. Oils slowly oxidize and generate stinky compounds which are desirable in cheese and no so other places. Stinky can accumulate in a poorly ventilated interior space like a case interior.

Re: Fitting drawers

#10

Jim DeLaney, Austintown, Ohio

Re: summary of procedure

Jim DeLaney, Austintown, Ohio

"With a block plane or spoke shave I plane a concave edge on the top of the back so that there is no risk of the back top edge dragging on the drawer dividers. It will be concave by about 1/32". "



Don't you mean CONVEX edge?

Re: Fitting drawers

#11

Consider Zinsser

Bill Tindall, E.Tn.

Zinsser Bullseye is a 3 pound shellac that sells for about $45 gallon. Consider what it would cost to make this product from flakes? As a bonus it lasts for a few years. It is light amber and waxed. Just right to provide a low sheen coating for drawers and case interiors.

Re: Fitting drawers

#12

Re: Consider Zinsser

Brian Holcombe

I have some Zinsser, I'll put it to use on the drawers as it is the only waxed shellac that I have.

Re: Fitting drawers

#13

Re: summary of procedure

TomD

I think he means a transverse dip the section of the edge would be convex or square, since it doesn't engage, it doesn't mater that much. This is a standard detail.

Re: Fitting drawers

#14

Re: summary of procedure

Bill Tindall, E.Tn.

The middle of the drawer back is lowered relative to the ends. I think that would meet the definition of concave.

Re: Fitting drawers

#16

Adding the stops

Bill Tindall, E.Tn.



This task is described in more detail on the Main Message board.