New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Recommendations for Scraper Plane

Posts

Recommendations for Scraper Plane

#1

Recommendations for Scraper Plane

howard gorman

I had posted this on the general message board. Tired of using the card scraper by itself, my hands are just getting too sore. So I am thinking of either a scraper plane or the current versions of the Stanley #80. I would appreciate all thoughts on this. Thanks.

Re: Recommendations for Scraper Plane

#2

Re: Recommendations for Scraper Plane

Chuck Bjorgen

I also have had problems using card scrapers. Have probably lost hand strength. The Stanley No. 80 cabinet scraper does work well for me though. Getting the blade prepped is important although you'll run across variations on this. There are several you tube and other instructions available on the Internet. I happen to like the video tutorial by Paul Sellars in his Masterclass series although you may need an account (non-paying) on his web site to view it.

Re: Recommendations for Scraper Plane

#3

Re: Recommendations for Scraper Plane

TomD

I Have the LN for rods, it is very nice, but has that limited use for me. I have the Kuntz 12, which is apparently a version of the Stanley, and it is good, but it is a side by side handle version if you were looking for a fore and aft. The currently available 112 is the same deal in for and aft handles. It doesn't take a terribly sophisticated tool to do a really good job. Just drop the blade till it rest on the surface, tighten the thumbscrew, then you can lower the blade very precisely off the cant mechanism.

One still needs the card scrappers. My favourite is the LV. They have some that are super thin, and they cut like crazy. They are a lot easier on the hands. Doubtless if one uses fine scraper where a thicker one is indicated there is some effect on the control, but so far I don't see any problems. One thing is they get hot, normally not an issue, but when it is it can be an all of a sudden thing.

Re: Recommendations for Scraper Plane

#4

Re: Recommendations for Scraper Plane

TomD

Sharpening wise I have tried everything. Turn around seems the most important. Since I have various tools for making tools I just eyeball them square to a belt sander then rub them out with the LV oval tool. LV is 13 KM from here. They deserve the commercial but in my case they are my local hardware. But if there was a carbide drill bit or a piece of drill rod around I would grab that. The oval tool is really cool, but everything works.

Also, I use a mill bastard file if the belt sanders are under a ton of dross or something.

Sharpening this way takes less than a minute, quite a bit less. There are other methods that use multiple stones, and all that jazz, they are way less efficient over time.

Re: Recommendations for Scraper Plane

#5

Re: Recommendations for Scraper Plane

Patrick Gibbons

I like the LV scraper holder when using the scraper for long periods.

http://www.leevalley.com/US/Wood/page.aspx?cat=1,310&p=32669

Re: Recommendations for Scraper Plane

#7

Re: Recommendations for Scraper Plane

Derek Cohen (in Perth, Australia)

Howard, as you know, I posted this on the Messages forum in reply. Posting it again here for others to read if they do not go there.

I prefer cabinet (card) scrapers to scraper planes. I use them to remove small sections of tearout rather than smooth a face with difficult grain. In that regard, a smoother with a closed up chipbreaker works well.

One of the cabinet scrapers I really like is simply a 3/16" thick section of a plane blade. This has a burr raised by grinding on a 80 grit CBN wheel, which takes seconds to do.


The thickness of this blade means that it does not get hot in the fingers.

This is how it is prepared ...


Of the scraper planes, I have only used the Stanley #112. A more modern version of this is made by both LN and Veritas. I have had good results with mine, but really have not used it in years. I also quite like my old Stanley #80, which was used for glue lines, until I began using a cheap carbide scraper.

Regards from Perth

Derek

Re: Recommendations for Scraper Plane

#8

Some Thoughts on Scraper Planes, etc

Christopher Fitch Memphis

I meant to type up this reply a few days ago but I was busy.

In any case, here's my thoughts on your question (I noticed over on your power tools post that you have the Veritas Holder).

I have a decent amount of scraping tools: A variety of Cabinet Scrapers, Two Scraper Planes, and a few other scraping tools.

- First I have the Veritas Scraper Holder. This is a fine tool that I've had for a while. It is versatile and really helps with holding scrapers. It holds quite well and you can even vary the curve you want on the scraper itself by turning the knob in the center. Of course it has a large benefit in that it uses standard card scrapers and you can just take it out if you need to. You said you have this so you should know all about it. I've mentioned these details in case anyone else is interested.






- Second I have the Veritas Cabinet Scraper that is similar to the old Stanley Scraper. Another fine tool. It's meant for scraping wide surfaces. You can vary the curve on the scraper with the knob.




- I have the Lie-Nielsen Cabinet Maker's Scraper Plane which is similar to the Stanley No. 85. Beautiful and well-made tool. Handles tilt so you can get right against a side while scraping.


- I have the Veritas Scraping Plane that is similar to the Stanley 112. You can buy a heavy blade that cannot be curved. Easily adjustable.


With all this, here's my thoughts after using all these items for a number of years. if I just had to have one tool, it would be the Veritas Scraper Holder. It's worked well for me. I know you mentioned you still have issues. I can't really offer anything in regards to that since it's worked fine for me.

If I had to buy something else in addition to the Veritas Scraper Holder, I'd get the Veritas Scraper Place. It's a plane...and it's easy to use. I used it a week ago to scrap some knotty cedar and it worked fine. It is a bit heavy but that's not an issue for me. It's easy to adjust and the blade is easy to maintain.

I'd say you can do the bulk of your scraping with that and then use your scraper holder for local areas and a bare scraper for tight spots.

I would not get the other two tools. Please note they are both good but I never use them.

The Veritas Cabinet Scraper is a bit unwieldy compared to the Scraper Plane. It's heavy for it's size and I find it harder to control in use compared to the plane.

The Lie-Nielsen Cabinet Maker's Scraper Plane is a well-made and beautiful tool with excellent handles. However, it's a very very specialized tool that has very limited usefulness, at least for me. You could use it as a general scraper plane but you cannot curve the blade and you have to contend with the corners on the blade. Also, the blade is smaller and you would need to work alot to cover the same area is a regular scraper plane. Unless you have a need for it, I advise against it. If you do need its unique abilities, then you won't be disappointed in it.

I don't have anything to say about the Lie-Nielsen Large Scraper Plane other than two things: I'm sure it's well made and you *cannot* curve the blade like you can with the Veritas version nor can you have a thinner or thicker blade option like the Veritas (this is what caused me to buy the Veritas over the Lie-Nielsen years ago).

That's about all I can say...hope this helps

Re: Recommendations for Scraper Plane

#9

Also...

Christopher Fitch Memphis

here's some additional comments on scrapers.

I would say that an excellent set of scraping items to get is the following:

- Veritas Scraper Holder

- Veritas Jointer/Edger

- Veritas Tri-Burnisher

I like the Jointer.Edger alot. I know it's not *needed* since you can just cut a slot in a block and grab a file but it's worked well for me. It doubles as a jointer for saw sharpening as well.

I love the Tri-Burnisher. It works great as well. Very easy to get a burr on a scraper with it. I had the Variable Burnisher...didn't like it so I gave it away.

It's too bad Lee Valley does not sell the above as a set instead of their current scraper set.