New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

I need a mortise tester

Posts

I need a mortise tester

#1

I need a mortise tester

Bill Tindall, E.Tn.

Is there something I can buy that will check the depth to see it is deep enough, and sides to see they are perpendicular, that will fit in small, say 1/4" mortises? A 4" square does nicely for larger mortises but it is too big for smaller mortises.

There is probably some machine shop tool for this task but I don't move in machine shop circles to know of it.

Re: I need a mortise tester

#2

Re: I need a mortise tester *LINK*

Hank Knight

Bill, Starrett and others make a simple depth gauge with a narrow beam hat would work for you. Starretts are pricy, but there are, after all, Starretts. I have one that was my father's that I seldom use, but I have used it to measure mortise depths.

The best thing I have found, other than my favorite little 4" double square, for measuring depth - and other things - is an inexpensive fractional dial caliper I bought years ago from Highland Woodworking in Atlanta. The narrow beam that extends from the end when you open the caliper is intended to be used as a depth gauge; and, as I indicated, it is useful for a lot of other measurements, like setting fences and such. This little fractional caliper is one of my most used measuring instruments. I think I oaid about $35 for it 10 or 15 years ago.

I don't know what to suggest for measuring square.


Starrett depth gauge

Re: I need a mortise tester

#3

Re: I need a mortise tester

GolfSteve in Calgary

Depth gauge, like that Starrett, works perfectly. It's also very handy for setting reveals and offsets and for setting marking gauges.

I picked up a very old depth gauge at a flea market in Australia for $10. Engraved with the name "Gary Cliff". On one side of the rule it is graduated in imperial 32's and 64ths. On the other side it is graduated in, if my memory is correct, decimal inches or maybe it's a strange scale that accounts for casting shrinkage. Kind of weird.

Re: I need a mortise tester

#4

Re: I need a mortise tester

Larry Barrett

Like Hank, a 4" double square is also my favorite and I use it for checking both depth of mortise and sides perpendicular to face. If you are chopping the mortise (as opposed to drilling) the double square finds high spots better than a depth gauge.

Re: I need a mortise tester

#5

Re: I need a mortise tester

wilbur

Just cut an L-shaped piece out of some scrap wood, where one arm of the L is the depth that you need. You just need a piece that is thinner than your mortise. Should take all of two minutes to make.

Re: I need a mortise tester

#6

Re: I need a mortise tester

John in NM

You could try something like this:


If used gently it would do for both functions you desire.

Downside is price, of course, and all those tiny little graduations :D 'course that goes with the territory.

Re: I need a mortise tester

#7

Re: I need a mortise tester

Bill Houghton, Sebastopol, CA

Starrett offers a couple of possible answers that will check depth and square both:

The 14D double square has 2-1/2" rules, including one that, according to the catalog I got from my uncle, is just 1/8" wide (their website does not state the width of the current rule, but it looks pretty narrow): http://www.starrett.com/metrology/product-detail/Special-Squares/Squares/Precision-Hand-Tools/Precision-Measuring-Tools/14D

If you do much work with slightly angled mortises, the 453 Diemaker's Square allows you to angle the rule slightly, or have it square. The 453C comes with the same skinny little rule: http://www.starrett.com/metrology/product-detail/453C.

Both of them are likely to cause your wallet to make little gasping noises if you buy at retail, but they show up on eBay for less.

I have the 453, and find it occasionally quite useful in its configuration as a square (as opposed to an angle measuring not-square); but it was an estate sale find at more of a bottom feeder price.

Re: I need a mortise tester

#9

Ultimate mortise tester TENON


Re: I need a mortise tester

#10

Re: I need a mortise tester

Brian Holcombe

Cut a piece of 1/4" thick material, make it long enough that it extends out of the mortise by a few inches, then use a square to check the outside.

Re: I need a mortise tester

#11

Check both depth and squareness together

Derek Cohen (in Perth, Australia)

I use a little Chris Vesper or Starrett double square. These have blades that are 1/8" wide and enable one to check both the depth and squareness at the same time. The wide blades of other combination square may only check the depth.

Regards from Perth

Derek

Re: I need a mortise tester

#12

Chicken and the egg

Bill Tindall, E.Tn.

One needs a well made mortise to insert the tenon. Of I had a mortise that accepted the tenon I would not need to test it.

Re: I need a mortise tester

#13

Bingo....

Bill Tindall, E.Tn.

I have a quality old fashioned caliper that has a thingy that sticks out its bottom when the jaws open. The bottom of the caliper sits flat on the top of the mortise and the registration of the part that sticks out will tell me if the sides are perpendicular to the face. No expenditure involved. thanks for the hint that led to a solution.

I don't do enough mortises to ever get proficient. Well in fact I do little enough of almost anything to get proficient. But with the aid of crutches I get by. By then end of 16 mortises I was getting better. These small ones go quickly.

The joinery in these bed side tables has become tedious. I have three drawers to make for another project and I may make them for a break in the tedium. I like making drawers.

Re: I need a mortise tester

#14

You're welcome 


Re: I need a mortise tester

#15

Re: Chicken and the egg

JDK

I agree. Cut the tenons fat, level them with a router, and using the router, ease them in. If the mortise isn't quite deep enough, cut a bit off the tenon, or dig out more of the mortise.

Re: I need a mortise tester

#16

Re: I need a mortise tester

Bob Entwisle in NJ

You need one of these


32nds on one side of the rule and 64ths on the other. The rule is 3/16" wide.

Bob in NJ

Re: I need a mortise tester

#17

Two sticks

David Charlesworth

I like two pieces of accurate scrap.

One represents tennon thickness but not width.

The other width but not thickness.

Since all mortices need space at the bottom, depth is not exactly critical and a biro line will suffice.

David

Re: I need a mortise tester

#18

like it 


Re: I need a mortise tester

#19

also recommend Chris Vesper's Double square

ian neuhaus

with mini blade. Not cheap, but accurate and small enough for a 5/32" wide mortice

Re: I need a mortise tester

#20

Re: like it

David Charlesworth

Forgot to add, that paring more than fluff, off the sides of a mortice was always considered bad practice.

The width should come from the thickness of the chisel used, and so be fairly uniform.

David