We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
Thanks for the link. I imagine that the leather for chairs would be thicker than the leather for lining the inside of a drawer ... ? (That is why I thought of bookbinding). Is there a difference?
They are in the chest I am building. There are three in all. The first is a single open "tray" (recess) that lies on the top of the chest, and is visible when the lid of the chest is lifted to reveal a mirror. This tray is used to temporarily rest earrings, etc when the mirror is used. Only the floor of the tray will have leather.
The second (and third - there are two) drawers are sliding trays (ala a tool chest), and these are fitted inside the top drawer. They will have several compartments, with the dividers in solid wood. As before, only the floors of these will have leather.
I have no idea what the difference is in the thickness of leather hides (such as from ebay) - and whether this should be an issue at all. I would prefer not to lose much depth, as the drawers are shallow already.
My thoughts run to glueing the leather to a 3mm section of sealed MDF (flatter and more reliable than thin chipboard or local ply), which may be dropped into the single tray at at the top. Similarly the two sliding trays in the top drawer, and then dropping the wooden partitions on top of them.
Medium thickness is usually 3-4 oz leather, which is around 1.2mm to 1.5mm. Very thin may be somewhat hard to find, but look at Brettuns' sheep and goat leathers.
My suggestion is to try Talas Leather in Brooklyn, NY. They are primarily a bookbinder supplier and have a wonderful assortment of products and colors. Not especially cheap, but quality usually isn't cheap. I use their Morocco grain leather for nearly all the grips on my musical instrument bows. A very high quality material. And the staff is nice and generally helpful. Hey, it is Brooklyn! (My Dad was born and bred in Brooklyn...)
If you can actually visit them with a small finished sample of the furniture piece to match color/texture, so much the better. BTW - if you are in the States and in the central NJ area and have a car, look me up for a visit!
One can find in the outlet stores in North Carolina large pieces of leather used to cover a couch, for example, in lots of colors. I will be near one next week. Leather from this source is vastly cheaper than buying a hide. An estimate of thickness is about 2 mm. It is supple and would lay flat. Email me off line if you want to pursue. I think I have 2-3 sq m in storage that I can measure and test as needed.
Leather is either veg or chrome tan. Books would be chrome. 1 oz = 1/64". Just bought some nice goat leather, is was 30 thou. Very fine chrome might be sold for socks (lining in shoes).
Can't imagine some crap like MDF near anything you make, what about aircraft ply, comes in thicknesses down to 1/32", maybe smaller, though you might need something like 1/16" to get the body you need to lie flat.
Did hear a fascinating use for MDF the other day, you can use it for vac jigs. It is so porous that if you seal the edges and top a vac table with it, it will hold stuff anywhere on it's surface, no need for drilling ducts and such. I'm a gonna be givin that a whirl.
Why do you want to buy leather in the USA? Looks like you have at least two local suppliers according to the interweb.
I have a local Tandy leather store. When I need leather I wander over there and pick up whatever seems best for the purpose. It helps to handle the hide to get a feel for thickness and pliability. Tandy has whole hides or different types and sizes of off-cuts and prepared pieces. Small pieces cost about $5-20 each. Local upholstery shops will also sell me off-cuts of leather.
For lining drawers, thin and supple leather is probably best (pig/calf/deer), and I would glue it down using either 3M spray glue, contact cement, or liquid hide glue/Titebond. If you're using a thin hide, I would worry that the LHG/Titebond might soak through the hide. I don't know what glue is best - but I've used all three in the past without problem.
I have no idea if different tanning methods will affect how rings, etc., might interact with the leather. Wouldn't want to tarnish your silverware.
Maybe you can find kangaroo leather...I hear that Koala leather is unsurpassed for lining drawers :-) Tasmanian devil leather is even better (*).
(*) I encountered a Tasmanian devil near Byron Bay, NSW in 1999. No one believes that I saw a devil that far out of it's normal habitat, but I have no doubt about what it was. Saw it sitting on a log and thought "aww isn't that cute." Then it opened its jaws about eighteen feet wide and hissed at me@!
Why do you want to buy leather in the USA? Looks like you have at least two local suppliers according to the interweb.
I have a local Tandy leather store. When I need leather I wander over there and pick up whatever seems best for the purpose. It helps to handle the hide to get a feel for thickness and pliability. Tandy has whole hides or different types and sizes of off-cuts and prepared pieces. Small pieces cost about $5-20 each. Local upholstery shops will also sell me off-cuts of leather.
For lining drawers, thin and supple leather is probably best (pig/calf/deer), and I would glue it down using either 3M spray glue, contact cement, or liquid hide glue/Titebond. If you're using a thin hide, I would worry that the LHG/Titebond might soak through the hide. I don't know what glue is best - but I've used all three in the past without problem.
I have no idea if different tanning methods will affect how rings, etc., might interact with the leather. Wouldn't want to tarnish your silverware.
Maybe you can find kangaroo leather...I hear that Koala leather is unsurpassed for lining drawers :-) Tasmanian devil leather is even better (*).
The reason asked about USA stores was to obtain links - most off advise on what to look for, and I am starting down this road without a clue what to use in the drawers. I know what look I want, but not will be appropriate by way of leather.
We have a local contact for Tandy (based in Sydney). There are a couple of stores in Perth, but they appear to be web based, so I cannot go in and look at the leather. I can send off for samples. There are also hides available on eBay but, again, one needs to know what to look for: thickness, etc. All these suppliers seem to expect that you know what to purchase.
Suede did cross my mind, but I prefer smooth and plain leather in an oatmeal.
This is an example ...
The lining will only be on the floor of the drawers. The oatmeal will contrast with the Jarrah of the drawers/trays, and not detract from the woodwork. I did consider midnight blue and aubergine as alternatives, but they begin to look garish.
Lining the drawers, bottoms only, will be very straight forward. You will need one basic tool, however, that is a half round knife that is used to cleanly cut leather. Very sharp sheers will work also.
You have a card scraper, I'm sure, I use one to remove some of the hair n the backside of the hide.
All of the hardwork in leather upholstery is going around corners, avoiding that will make it easy to make a clean looking install.
For gluing the leather to a substrate, is to stretch the leather out on a flat surface with the face side down. You might want to pin it out, with push pins, oversize.
Then spray a heavy coat on the substrate with a high strength contact adhesive, then lay that down on the leather, and press it down. You can then turn it over and smooth it out with your hands or a roller.
Spraying the leather might bleed through, and trying to place the leather on top of the substrate is not as easy as it might seem. You can knife off the excess after the glue is dry, using the edge of the substrate to guide your knife.
Then spray a heavy coat on the substrate with a high strength contact adhesive, then immediately lay that down on the leather while still wet, and press it down.
Keith's method is good and the wooden roller comes in very handy. Btw,mi use marking knives to make corners and so forth. For cutting leather it's important that the tools are kept very sharp. Making your cut all at once makes for a clean cut, multiple cuts leaves a mess.
That's funny, I used to get a mess when trying to cut it all in one bite - even with a straight edge the leather would tend to pull into the cut from under the straight edge. Started making two or three passes and then I'd get straight cuts. This was using a new utility knife, so I'm pretty sure dullness wasn't the problem.
Funny how opposite techniques can yield opposite results for different people, isn't it?
Derek-3M is one company that makes spray adhesive that works very well for skins like leather. It is used for high end upholstery work in vintage auto/truck restoration work, and leather is used more than any other material.
You can stretch out your skin, and glue a section of 1/8" hardboard to it. Once it dries, cut it to fit your drawer bottom all at once. Trying to glue leather into the bottom of a drawer is going to be a lot harder than it sounds, and will be difficult to get a "stretched" look.
I have made panels in this way, with very good results. I learned this from a guy who does custom automotive interiors. Roof liners and inset door panels are made in a similar fashion.
My thoughts (naive no doubt) are that the leather will be going into made drawers, and that it will be difficult to glue them (I have used the 3M contact spray, and it is excellent – but not practical here). Further that thin leather (about 1.2mm thick) needs to be stretched, and it is likely that thicker leather (about 2-3mm) will be easier to lay, as well not telegraphing the glue below it. That would make it possible to apply with a brush.
Now this is all a bit premature since I have now completed the drawers - which the leather is not for - and will be moving on to the handles and chest back this weekend. I will post pictures then.
It is after this that I need to build the upper section of the chest that houses the mirror - that will have leather. And then the jewellery trays in the upper drawer - those will also have leather. Lots of work - and a couple of months - before I need the leather. For now I am trying to educate myself what is needed and how to do it.