New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

So I made this Awl.....

Posts

So I made this Awl.....

#1

So I made this Awl.....

Bob Entwisle in NJ

Been way too quiet here on the handtool side. No one interesting posting anything, so I guess I'll have to post.


I made this out of a piece of tiger maple, a 1/8" dia. HSS tool blank, a bit of brass pipe. Wiped blo/turps on it and that's about it.

Bob in NJ

Re: So I made this Awl.....

#2

Nice work Bob!

Stuart Hough

I really like the shape of the handle. Keep it up!

Re: So I made this Awl.....

#3

Re: So I made this Awl.....

Bill Houghton, Sebastopol, CA

What type of awl is it? It looks like a brad awl or birdcage awl from the point.

Nice piece of work; if I'm right that it's a pushed awl rather than a scratch awl, the shoulder on the handle would give good purchase.

Re: So I made this Awl.....

#4

Re: Nice work Bob!

Bob Entwisle in NJ

Thanks Stuart.

Re: So I made this Awl.....

#5

Re: So I made this Awl.....

Bob Entwisle in NJ

Hi Bill,

It's a sort of birdcage awl, tri pointed.

Yes, push and twist for making/starting holes.

It's a first effort, sort of a prototype of both handle and blade. The handle seems pretty good in my hand, and yes I can apply good pressure to it. I think I'll try a more gradual taper to the point on the next one.

Thanks for looking.

Bob in NJ

Re: So I made this Awl.....

#6

Another awl

Derek Cohen (in Perth, Australia)

Hi Bob

I used one with a similar handle for many years. Then a year ago I built a couple that I considered to be more ergonomic for my hand and the way I use them (personal preferences). The idea was based on a birdcage awl needing to be twisted and pushed down simultaneously. This differs from a scratch awl, which I hold like a pencil.

I have made these in different steels. HSS is easiest to purchase. The one below is 1/4" square carbide, which came from Czech Edge (as a kit for the blade). The bevel has been reduced to 25 degrees (it comes with one at 30 degrees).


There was some discussion on Old Tools about the benefits of a three-sided blade, as you have made. It makes sense insofar as creating a coarser cut than the four-edged blade. Is that the reason behind your three-sides, or was there another consideration?

Regards from Perth

Derek

Re: So I made this Awl.....

#7

Question, Derek

Hank Knight

What did you use to grind the bevel on the carbide?

Re: So I made this Awl.....

#8

Re: Question, Derek

Derek Cohen (in Perth, Australia)

What did you use to grind the bevel on the carbide?

Hi Hank

First ground the sides using CBN wheels. Then honed it the rest of the way on diamond stones.


Regards from Perth

Derek

Re: So I made this Awl.....

#9

Re: Question, Derek

Hank Knight

Ah! I forgot you are a CBN proponent. I need to look into those. Thanks for the reply.

Re: So I made this Awl.....

#10

Re: Another awl

Bob Entwisle in NJ

Hi Derek,

I like the handle shape on the awls you made and intend to explore different handle shapes.

I was aware of the discussion on Old Tools and this awl is just a first effort, so I went for the tri point grind. It seemed like an interesting idea. I also was trying out an idea for a jig for the tri point that did not involve a hex shaped ferrule.

More awls to come in the future, i think.

Bob in NJ