New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Some marking tools

Posts

Some marking tools

#1

Some marking tools

Rum

Wanted to drop these here as a thank you to Derek Cohen for the inspiration as I mostly followed your doc at http://www.inthewoodshop.com/ShopMadeTools/A%20Knife%20for%20Marking%20Dovetails.html for the basic design on the marking knife and awl. Modifications were of course made for which I'll take full blame.

I actually did 4 sets of these, but they're all basically the same so just posting pics of the one set.

knife and awl, added a little carving which keeps them from rolling and adds a little positive gription on the bottom bits, the knots on the top part were just for fun.


Dual beam marking gauge, the brass pieces were hand filed to fit into dovetail slots in the front, but I epoxied them in anyway. The snail doesn't actually overhang quite as far as the picture here shows...


A box to put them in (also inspired by Mr Cohen, although I punted on the pivoting holder due to time limits, maybe next time)


Although my dovetails are far from as nice as his (its a learning process).


Mostly hand made, although the lathe used to do the initial turning on the knife/awl is powered, I used my neander-buddy (aka bandsaw) for rough dimensioning, and there was some powered grinder work required to convert the jigsaw blades and drill bits into cutting knives and awl points.

Re: Some marking tools

#3

Re: Some marking tools

Curt Putnam

Absolutely gorgeous! They're a gift for me right? :-)

Re: Some marking tools

#4

Re: Some marking tools

Derek Cohen (in Perth, Australia)

Beautiful work ... better than mine!

(and thanks for the compliment).

The carving must be tiny since the handles are the size of a pen. How did you do this?

Regards from Perth

Derek

Re: Some marking tools

#5

Re: Some marking tools

Rum

Thanks for the compliments!

Curt, these are unfortunately all spoken for already (or I'll be making a new set of gifts I don't have time to do heh).

The braids on the carving are perhaps a wee bit under 1/8" so not so bad. The rope work is a bit smaller.

One of the other sets with a ruler for scale (apologies on the lighting..) - I suspect? these might be a wee bit bigger than yours?


For the rope work I turned beads and then cut notches part way through at about a 60d angle (this is about 10d shy of the final angle which allows the ends to curve a bit) with a small carving knife followed by a couple of passes with a needle file to round the rope twists over. I kind of sweep with the needle file to get it round and bring the tips of the points over a bit.

For the braid/knot work the main problem is layout, I usually tie the knot a few dozen times right before carving it to get it fixed in my head (although simple three strand like on the awl isn't to bad, the one on the knife is a tucked through crown and wall combo isn't as firmly in my head). Again I turned a bead (but with fairly square edges) and then drew the knot on it. Then I used a couple of small chisels (one straight point and one skew point mostly) and a small chip carving knife to do the bulk of the material removal. I cut small nicks at the crossing points first to delineate which pieces go over or under and then work back from there forming the strands. At this point its almost like "working a knot" tight where I just keep going around and refining the shape more, usually takes 5-6 passes before it looks ok. Once the bulk is done I clean up the curves a little with the small needle files and one of the two cherries micro gouges I picked up at the TFWW scratch and dent sale last year (I think its a 1mm) to hit the inside corners. That's about all there is to it.

Mostly its just patience, time, and careful layout.

When I'm feeling less neander I've cheated and used some small bits in the power carver to do smaller things like this button and micro crochet hook in ebony. The cleanup was done by hand at least ;)


Re: Some marking tools

#6

Re: Some marking tools

Steve Voigt

Tremendous work! Congratulations!