New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Wrapping a case with mitered molding

Posts

Wrapping a case with mitered molding

#1

Wrapping a case with mitered molding

Bill Tindall, E.Tn.

A common task in furniture building is wrapping a case or top with molding mitered at the corners. I do not recall ever having seen this practice taught in a book or article (I am sure it has; I am just saying I haven’t seen it). This operation can be stressful. The molding pieces are often cut from a continuous length for grain matching, so screwing up one section means starting over with a new piece of molding or sacrificing the grain matching. And, because it is molding, designed to be a focus of the piece, the joints must be near perfect.

I have evolved a strategy for measuring, fitting and attaching mitered molding that works. But I have lingering doubts whether it is the best approach. How do you all accomplish wrapping a mitered molding about a case, in this case a Spice Box?

In the example illustrated I am wrapping the molding beneath the case top with the case upside down, except for the final picture which shows the bottom moldings installed and the case upright.

PIC1

1. From the front of the case I arbitrarily work from right to left. Let us call the left molding piece #1, the center #2 and the right #3. I begin by cutting the #1 molding piece a bit long. The miter on the end of the remaining molding stock is also cut as seen in the picture.

2. I test the miter fit. If it is not perfect, a common occurrence either because the saw is not set up perfect or the case isn’t square, I adjust the miter angle either by resawing or with a shooting board.

PIC2

3. A wisp of wood is taken from the inside corner to help ensure the molding seats tight against the case.

4. I press the miter together with finger pressure and mark the final length of the #1 molding. I may cut this piece to its finished length, or if unencumbered for sawing later, I leave it long and cut off the overhang after installation.

PIC3

5. I typically nail molding on, so at this point I drill pilot holes, add glue to the front third of #1 and nail it on. The precise positon of #1 is established by hand holding section #2 in position to make a tight miter joint between #1 and #2.

6. #3 is now cut oversized with a miter on one end

7.Next is the hard part. Using hand held test fits #2 is trimmed to length so that it fits near perfect between #1 which is now fixed to the case and #3 held in position by hand. The length of #2 must be right to a tiny fraction of an inch. A shooting board, a devise that enables a few thousandths of an inch to be removed from the mitered end, is a reliable means of getting the length right. In the case of this small molding I could not hand hold it in on the shooting board against the force of the plane so I had to saw it to length. I need to work on this problem.

8. When it seems to be of the correct length pilot holes are drilled for nails ( I usually use snipped-to-length brads from the pneumatic brad nailer) and glue applied to molding back and miter. The miter between 1 and 2 is brought together with hand pressure and the molding is nailed on.

9. It is now a simple task to install #3 similar to how #1 was done.


Re: Wrapping a case with mitered molding

#2

Re: Wrapping a case with mitered molding

Paul in NJ

I start with the front/center piece of moulding. I transfer the length directly from the case to the center of the moulding with a striking knife. I cut to the line and apply to the case. Cut the miters on the side pieces. Test for fit, adjustments are made to the side mouldings. Cut to length.

Paul Dzioba

Re: Wrapping a case with mitered molding

#3

Questions

Bill Tindall, E.Tn.

Your way is quicker, but seems more risky. The questions involve minimizing the risk.

1. Miters don't always close for me on the first try. Either the saw is not set exactly 45 degrees and/or the case is not exactly 90 degrees ( a situation that is getting rarer :) ) Hence, I need a test fit of the miter on the corner involved. Do you do some sort of test fit of the angles that was not mentioned or are your cuts reliably 45 and corners 90?

2. Clearly in principal one can mark the length of what I am calling #2(front molding) , from the front of the case. In practice if find marking the length off the case front unreliable. Maybe the case corner is slightly rounded or I don't know what, but I often don't wind up with the length of #2 being sufficiently accurate. Any hints to success on this step?

3. How are you cutting miters?

Re: Wrapping a case with mitered molding

#4

Re: Questions

Paul in NJ

1. The case is close to 90 degrees. I cut the front moulding ends at 45 degrees. I cut the side mouldings at 45 leaving the length long. If the miter does not match to my satisfaction, I pare the side mouldings with a very sharp wide chisel. If the case was not very close to 90 degrees, the joint will be closed but there will be a hair overlap of the moldings. You can do a few things if there is some overlap. You can burnish and roll over the edge, pare it back, or sand it back.

2. I use a single bevel striking (marking) knife holding it flush to the case. It helps if you can clamp or tape the mouding so it does not shift when marking. Afterwards I use a miter square to mark the angle.

3. If I am building a period piece, I use period methods from start to finish. This gives me great satisfaction and sort of "connects" me. That said, I use a xcut back saw (14 point). I start the cut from the back following both lines simultaneously. Before the saw breaks through the front show surface, I rotate the saw in the cut so that I am now cutting through the front to the back, eliminating any breakout. Unless I am breaking down stock, I always cut to the line.

For contemporary pieces, kitchen cabinets, and picture frames I will use a sled on my table saw. The sled has two fences so that you cut complementary angles that always match. I will use a sliding miter saw for pieces too long and awkward for the sled.

Paul Dzioba

Re: Wrapping a case with mitered molding

#5

thanks

Bill Tindall, E.Tn.

do you have a picture of your saw sled?

Re: Wrapping a case with mitered molding

#6

Re: thanks

Paul in NJ

Will try to remember to take a picture tonight.