New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

slipping veritas plough, Eureka!

Posts

slipping veritas plough, Eureka!

#1

slipping veritas plough, Eureka!

Edward in Vancouver

I've always been plagued with the depth stop on thee Veritas plough, Like Lucy with her football, it always slips at the last minute. I've roughened the post with horizontal scratches, roughened the casting slot with horizontal scratches, but it still slips. Taking Derek C's advice, I cut a slot in the adjustment knob for better tightening with a screwdriver. Result? I snapped off the threaded portion from the knob, had a devil of a time getting the remnent out.

I was sorting out some junk today and came across a firm rubber washer, maybe 1/2" in dia and maybe 1/16" thick and a light bulb went off. I laid the washer over the threaded hole on the plane body, placed the clamp on top of this, laid the wave washer on top of the clamp, and threaded the knob home.

With "moderate" finger pressure on the knob, I can't get the depth stop to budge!

Try it. It won't cost you anything and there's no modifications to make to your plane.

Re: slipping veritas plough, Eureka!

#2

Re: slipping veritas plough, Eureka!

Derek Cohen (in Perth, Australia)

Edward, you must have cut the screwdriver slot very deeply for the one side to have broken off. Sorry to hear my suggestion created a problem.

I have added slots to all my lock down screws, and they work as desired. Still, the rubber washer idea sounds an easier modification, and worth trying first.

Regards from Perth

Derek

Re: slipping veritas plough, Eureka!

#3

Re: slipping veritas plough, Eureka!

William Duffield

Thank you for the valuable tip. I've had the same problem with mine the last time I used it. It was very annoying when I found the groove I was plowing was deeper than I had planned. I assume Lee Valley replaced the knob you broke? I'm sure they will if you ask. In any case, make sure you notify them of your enhancement, so they can work it into their product improvement program.

Re: slipping veritas plough, Eureka!

#4

Re: slipping veritas plough, Eureka!

Edward in Vancouver

Actually, the slot was cut very shallow, I just torqued the knob too much and the threaded portion snapped off. Hmmm...please don't read into that last sentence too much professionally..... :D :D

Maybe I should contact Veritas with this, but I'd rather a few more people try it out before I do. It is pretty harmless (and cheap!) and totally reverseable.

Re: slipping veritas plough, Eureka!

#5

Re: slipping veritas plough, Eureka!

Derek Cohen (in Perth, Australia)

Hi Edward

Here is what I recommend - and still do - for the life of me I cannot see how this could have cause a cheek to break off. The knob is solid brass ...



I have done this on all the knobs on all the planes, including the fence knob on the router plane.

The obvious reason for the screw slot is that this enables the clamp to be tightened more. The other reason is that it enables the knob to be loosened more easily. All without damaging the knob (otherwise one is forced to resort to vise grips, which tear up the knurling).

I shall give your rubber washer idea a go. It is less invasive than my method.

Regards from Perth

Derek

Re: slipping veritas plough, Eureka!

#6

Re: slipping veritas plough, Eureka!

Brian Roberts

I don't see where he said the "cheek" snapped off....did he not say the entire knob separated from the threaded portion?

Re: slipping veritas plough, Eureka!

#8

Re: slipping veritas plough, Eureka!

Brian Roberts

A BIG screwdriver! lol