New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Help me find mallet plans

Posts

Help me find mallet plans

#1

Help me find mallet plans

Steven

Hello all,

It's been many years since I've posted, but I'm coming back to the flock and hope someone can help me. I experienced a hard drive crash a few years ago and lost many articles and plans. What I'm hoping someone can help me with is a mallet plan that I lost. The original was for a turned mallet that was made out of apple wood. what was unique about this mallet is that it used 3 "center" points to turn the mallet which resulted in a mallet that was sort of curved (hope I'm explaining this clearly). The handle was also held together with a very unique wedge in the handle, which for the life of me I can't remember what it was called.

Anyway, I hope this very vague description rings a bell with someone and they can direct me to the original site with the plans.

Re: Help me find mallet plans

#2

Re: Help me find mallet plans

John Sayles

might you be thinking of a "fox (or foxed) wedge"?

Re: Help me find mallet plans

#3

Re: Help me find mallet plans

TomD

http://www.mikes-woodwork.com/OffsetMallet.htm

Re: Help me find mallet plans

#4

Re: Help me find mallet plans

Steven

YES!

That is exactly the mallet I was talking about. This webpage is much better than the plans I had though.

Thanks very much!

Re: Help me find mallet plans

#5

Neat!

Tony - Memphis

That's a neat idea/technique. May have to try that. I made a square mallet and angled the faces to get a similar affect. Hmmm, I may mess around with the offests in Sketchup to see what angle looks good.

Thanks,

Tony

Re: Help me find mallet plans

#6

Ellis Walentine

Be careful

Ellis Walentine

I'd be very careful about the author's advice to use a chop saw to trim the head after turning. I make a point of avoiding cutting round objects with chop saws. Likewise with bandsaws. It is done all the time, but disaster lurks.

Also, you might want to mock up your swing, to see what angle works best. The idea is to have the face of the mallet arrive squarely on whatever you're striking.

Ellis

Re: Help me find mallet plans

#7

Agree...

John in NM

I approach unsupported cuts on the bandsaw very carefully and never ever do them with a chop saw. One can get away with it for years, right up until the time they don't. With the chop saw, it is usually the round drop piece that bites you, or rather the blade bites after you jump when the drop piece goes flying with a loud clang or hits you.

Re: Help me find mallet plans

#8

Re: Be careful

TomD

It's funny. I used to make all kinds of risky bandsaw cuts a la Maloof (no such results), and on bowl stock. Never had a problem until I got my "good" saw. HP makes quite a difference and more isn't always better.

Anyway, in this case you can saw the end with a hand saw, and clean it with a plane, if you can find a way to hold it.

Re: Help me find mallet plans

#9

Re: ditto that...

david weaver

..saw power. I appreciate a tablesaw that's a little bit underpowered. The only kickback I ever got was off of a large 5 horsepower cabinetsaw, and it didn't hiccup at anything, and its weight let it get a pretty good amount of giddy up on the piece it flung.

Re: Help me find mallet plans

#10

Don't count on low horsepower...

Paul M

My tiny inca table saw with low horsepower gave me a kickback to the crotch a couple of months ago. That resulted in a very large and uncomfortable bruise. The thin piece of cedar was so light that it picked up speed super fast. I could see individual teeth marks on the end of the launched piece that were the exact spacing of the teeth on my blade, so it made it up to maximum (warp) speed. It actually punched a hole in my denim jeans.

I've done my last through cut that I will ever do on that saw. From now on, only delicate grooving cuts that require precision (like saddle slots on guitar bridges, or fret slots for fingerboards) will be done on that saw. I got into hand tools because of the dangers of power tools, and this was a great but painful reminder that I really really really hate power tools.

Re: Help me find mallet plans

#11

Good reason....

John in NM

To have a nice heavy leather apron. Although leather isn't really inexpensive, even when bought as a side, it is fun to work with.