New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Images in wood

Posts

Images in wood

#1

Images in wood

Wiley Horne--So. Calif.

Hi All,

For many years, a particular image has stuck in my head. Here it is:

https://www.flickr.com/photos/78661951@N07/9482947006/in/set-72157635012252891/

How would one render some approximation or essence of this image onto wood? The only thing I come up with is to focus on the darker layer, and try to inlay that, so that it would be slightly raised above the ground of the panel. Maybe a quilted maple panel to try to simulate rain and mist.

Any thoughts?

Wiley

Re: Images in wood

#2

bridger

Re: Images in wood

bridger

Several possibilities come to mind.

In marquetry subtle shades can be created by darkening light colored woods with heat. Also, woods come in lots of colors without heating or staining.

Laser engraving could do it, but where's the skill in that?

Low relief carving can be used to make very fine gradations of shadow, best viewed by oblique light.

Re: Images in wood

#3

Re: Images in wood

William Duffield

I also would use marquetry, but I would inlay all the light colored leaves and stems into the background first, then make a new sanwich and inlay the dark leaves into what you built first. Definitely, sand shading, as Bridger recommends, should be used if you cannot match the color gradations to some dark figured wood.

A good place to start learning how to do this is with W. Patrick Edwards' American School of French Marquetry. He has several excellent instructional videos online.

https://www.youtube.com/playlist?list=PLqT3xhD7hrpBIJ5FSAz9a3jM07WcavsT6

You don't need to build a chevalet, but his kit is a lot less than an Excalibur scroll saw (or even a DeWalt).

You might even consider an introductory course or two from him. He's close to you, in San Diego.

Re: Images in wood

#4

Have it printed on? *LINK*

Dick Coers

Not in keeping with hand tools, but another option


posterjack

Re: Images in wood

#5

Ellis Walentine

Paint

Ellis Walentine

My wife is a painter and she and I collaborated on numerous projects over the years, including dressing screens, toy boxes, frieze panels and others where we wanted decoration without the effort of a full-bore marquetry treatment. I suspect that painting your bamboo image might be the best way to do this. After all, the original is a painting. Practice a bit with gouache or thinned acrylic, or oils for that matter. It'll be easier to capture the lightness of the original in paint than in wood. Of course, it also depends on what you're making. There might be arguments for marquetry.

Ellis

Re: Images in wood

#6

Re: Images in wood

Paul M

Hi Wiley,

A friend of mine not on this forum made a blanket chest using intarsia marquetry to inlay a bamboo pattern. It's the most beautiful wooden object I've ever seen. I'll have to ask him to send me a photo and seek his permission if I can post it here.

Paul M.

Re: Images in wood

#7

Pyrography

Bob Hackett

I know people who do work that would be hard to tell from a black and white photograph.

Re: Images in wood

#8

I'm thinking, Sandblast those gray leaves

Keith Newton

But inlay the dark, but maybe sandblast them as well, but then go back and paint them.

Or you could sandblast the whole background, leaving all leaves and stems raised, but then paint of tint the darker ones.

Another option, would be to use a soft wood like Western Red Cedar, where you get the feeling of distant hills or background patterns from the annual ring pattern, then do an incised carving, which you would later darken some of the leaves with paint, or even pencil. I did some things like this back in the early eighties, but like so much of my older work, I don't think I have any digital images to share.

Re: Images in wood

#9

Re: Images in wood

ian in Sydney

I'm thinking intarasia or inlay using sand shading to get the graduation between very dark and dark

Re: Images in wood

#10

Re: Images in wood

Mark Mandell - Gone Round In New Jersey

I would start with a blasting "mask". Print your image onto a piece of 10-12 mil film, then cut out the faint (background/light) leaves as you would if making a silk screen. After surface prep (sanding/carding, etc), place the mask and hold tight, then blast the exposed wood surface. I would suggest glass beads to lightly dent or "peen" the surface rather than cut in with sharp sand.

Dark "foreground" leaves and stems can be cut from thin veneer, glued, and then softened by hand to leave them just proud of the surface without actual inlay. Lastly finish as usual so that the peened surfaces comes up as ghost images in the background.

If you wish to carry the process even further, make two masks of leaves with one to be given more texture that the other. It will then operate as a mid-ground by being slightly darker. You can also vary the color of the veneer additions to introduce another mid-ground, but going too far for too many levels will likely break the effect.

Obviously, try this on scrap first.

Re: Images in wood

#11

Re: Images in wood

Wiley Horne--So. Calif.

Wow!! Thanks to all of you, for your carefully considered thoughts. I believe any of the approaches suggested--sand-shaded marquetry, pyrography, texturizing with bead or sand blast, raised marquetry with hand texturing--could work given enough skill and patience. I am much tempted by having it printed, also!

The ink effect--that things are impermanent--sort of works against the aesthetic of wood, which is that some things are forever. So I will have to try a couple of your ideas, and see what happens.

Again, thank you very much for an eminently usable set of approaches, all of which have much to commend them.

Wiley

Re: Images in wood

#12

Re: Images in wood

Mark Mandell - Gone Round In New Jersey

Wiley,

Notwithstanding this is the Hand Tools Forum, laser engraving that image would be an easy putt for a tech, even to differing depths or such that you could then inlay with different shaded epoxy and then reflatten and finish for a durable "reproduction" of the image.

Re: Images in wood

#13

Re: Images in wood

Wiley Horne--So. Calif.

Thanks Mark,

I've heard of laser engraving (Darrell Peart does it with Greene & Greene complex inlay, for example), but have no knowledge of its capabilities. So your post is very helpful.

Any recommendations for someone who does laser engraving?

Wiley

Re: Images in wood

#14

Laser Guys

Mark Mandell - Gone Round In New Jersey

You'll find'em all over the place; easy in your phone book. Most every trophy store uses laser engraving to do their plaques etc. and they will be only limited by the size of their rig.

You give them the piece and a copy of the image in pdf or jpeg format and shazam! you've got it.

Re: Images in wood

#15

Re: Something you can do yourself

TomD

Is to print the picture using a laser printer like my Laserjet 6l I picked up for 10 bucks. You turn the print over and secure to your piece of wood, then you wipe it with acetone. The print will transfer top your wood with great accuracy. I guess you could call it a day, but it is also a method of transfering the outlines for carving or pyrography. You could inlay with mother of pearl, or something.

You get one shot with the transferring. You can of course simply print a new sheet, but if you don't get he transfer in the first go, it sets the ink. So experimentation would be wise before putting it on a final piece of wood.

There are lots of other ways of transferring images, and special products to suit different printers, like the Epson 888. Look at T-shirt sites. I use the method mentioned to lay out very accurate transfers on met

Another option for CNC is photo carving:

https://www.youtube.com/watch?v=XIv8Wq-ywlI

Re: Images in wood

#16

Re: Something you can do yourself

TomD

Sorry, that hung on me before I could finish it or correct it.

I was saying I used the method to transfer to metal, leather, wood, etc... The marks are permanent.

Normally with a picture like that I would upload the photo, then outline it with lines, then delete the picture. That way I would get sharper lines for something like carving or routing.

You can always count on someone having done your graphic on a guitar, a little flashy.




Re: Images in wood

#17

Re: Something you can do yourself

Paul M

Nice work on the guitar Tom!

Here's a picture of the blanket chest that my friend made that I mentioned above. Bamboo works wonderfully as marquetry:


img

Re: Images in wood

#18

Tom and Paul, those are both convincing

Wiley Horne--So. Calif.

methods! Paul, that marquetry is magnificent (thanks to you and your friend!) and illustrates the degree of shading one can achieve.

Tom, that acetone transfer from a laser print seems compelling. I will pursue that to see if I can find one not brand new.

Thanks to you both,

Wiley

Re: Images in wood

#19

Question for Tom

Wiley Horne--So. Calif.

Tom,

To do the acetone transfer from laser print, what kind of paper did you make the laser print onto?

Wiley