New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

making a strop

Posts

making a strop

#1

making a strop

McKay

When I was young, I remember the barber and also my grandfather having a leather strop. Everything that I have seen on this site says to place the rough side up. However, the old ones that I have seen seem to always have the smooth side. Does anyone know what it really should be? Thanks

Re: making a strop

#2

Re: making a strop

david weaver

No person shaving would ever use the coarse side. It literally will not finish a razor edge to a suitable sharpness, and on harder leathers it can damage the edge.

Tools are less sensitive to some extent, so it doesn't matter as much.

I personally use the smooth side on tools, too. It's more instructive - if your edge is finished, smoothed leather shows no marks. If you have wire edge remaining or a part of the edge not done well, it will track lines on the surface of a smooth strop.

Also, eventually the strop gets dirty and bits and pieces like metal wire edge fragments or unwanted grit gets on it. It's far easier to clean those off of a smooth side, or even sand the surface, than it is to do it with the rough side.

Re: making a strop

#3

Alteratives

Derek Cohen (in Perth, Australia)

Hi McKay

This is not really what you requested, however it may eventually be preferred.

I have been down the strop path for many years. I have several, the best from Tools For Working Wood, which is 1/8" thick and hard horse butt leather.

Leather strops have a place, and I would argue that this is largely for curved blades, such as used for carving. I have stopped using them on bench chisels and plane blades.

Some prefer to use green compound (0.5 micron) on MDF. I am not a fan of this as the sealed surface is eventually eroded and the grit underneath will be rough.

I prefer either green compound on planed hardwood, such a smoothed Jarrah.

Or I will use 0.5 micron diamond mesh from Lee Valley (0.01 micron is also available). I glue perspex to hardwood, and then place the self-adhesive diamond mesh on that surface. Do not run a ragged edge on this mesh as it will tear. Otherwise it lasts a very long time.


Regards from Perth

Derek

Re: making a strop

#4

Re: Alteratives

david weaver

(not saying this to be argumentative)

The MDF strops won't gain any roughness if the crayon is used consistently. They will instead glaze, even as the burnished surface is worn off of MDF. A drop or two of oil even on bare MDF will mitigate the rough and allow it to be burnished.

I have found that when using one, which isn't something I do often any longer, that it's helpful from time to time to keep a junk card scraper to take a pass or two and remove most of the swarf.

A drop or two of mineral oil helps the action of the MDF and ensures that you continue as a user to burnish the surface of it.

I like horse butt, too, for compound - when it's glued to a backer, it's really not much different from MDF, though - it's halfway to wooden.

Butt strips can be found on ebay and out on the internet for an inexpensive amount if one wants to cut their own strops. The TFWW option looks good for someone buying, *but* leather cuts very easily with a marking knife and a straight edge - especially horse butt which isn't as thick - and for those of us using strops in various places, it's helpful to have a good smooth bovine section and a horse butt strip. The combination of the two should be about $50 and yield dozens of strops, a handy thing if one ever contaminates a strop with something by accident.

That said, a contaminated strop can be sanded if scraping doesn't remove the contaminant. veg. tanned leather sands very well (just brush it off or vacuum it afterwards), and a treatment of mineral oil on the sanded surface yields an almost uniform smooth surface near immediately.

(I have almost the same problem with strops as I have with stones, but not quite so bad. And I only make my own, something I haven't yet tried with stones! But I've been through various veg tanned horse and bovine, and also bought a cordovan shell from horween several years ago - the latter is not useful for tools, too expensive, but it is available if you know who to ask, contrary to popular belief. You me and everyone else are just last in horween's line - they will not ship a shell until they have satisfied orders for shoe makers and others who are large customers, and it's extremely expensive (about $300 delivered for a shell that is two or three square feet - but it makes an interesting razor strop and it is in such demand that a mention of having excess will have watch band and wallet makers you've never met asking you if you'd like to sell your scraps to them)).

Anyway, I do think this is one thing - strops - where it's worth it for a woodworker to get some leather and experiment. Everything but the horween is cheap, and it's not my first choice for razor strops even because only the factory surface is what you want, and while the shell itself is very durable, the surface treatment can be damaged easily. And the surface treatment is the real treat in the whole deal - definitely way out of bounds for tools. Way out, and I think a desirable razor strop just because it can be used immediately from horween and because it's expensive.

Re: making a strop

#5

Re: making a strop

Patrick Gibbons

I've always used the smooth side, whether the leather was charged or not.

Re: making a strop

#6

Re: making a strop

TomD

I glue full grain leather smooth side up, and I get hard good quality stuiff, a lot of what is out there these days is about as hard as marshmallow. It would be a pretty rare need to glue down the smooth side since the only reason to have a smooth side is if you are going to use it, and gluing it down to hardwood doesn't seem like much of a use. Given that split grain in a lot cheaper, there will likely be someone who is willing to flog the stuff as better. Seems like horse would be better, but I don't have any direct experience with it.

Re: making a strop

#7

If you like hard leather...

david weaver

you would like a horse butt strip.

I have not used this particular vendor, but the price looks in line.

2-3 SF for $22 plus shipping.

http://www.zackwhite.com/79-oz-Genuine-Horse-Hide-Butts--Z4509HS_p_5306.html

I recall ordering a butt strip off of ebay, but I paid more. Still, I have gotten so much use out of it that I don't care. It is so durable that I may use the razor strop for several decades, and I have two other wood strops and still half of the leather is left. If you contaminate it, you can sand it, it almost sands like wood when it's good to wood.

Re: making a strop

#8

Re: If you like hard leather...

TomD

Thanks, I know of ZW by reputation, but I haven't ever looked at their site. Lots of interesting stuff.