New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Silly question of the week... eggbeater drill

Posts

Silly question of the week... eggbeater drill

#1

Silly question of the week... eggbeater drill

Joe in a Cleveland suburb

I picked up a Miller Falls eggbeater drill over the summer at an antique shop. Cheap.

Cleaned it up, seems to work fine.

Question though, how are you supposed to tighten the chuck firmly on the drill bit? I almost need a third hand to hold the drill, the wheel, and tighten the chuck.

Oh, it didn't include original drill bits which I am thinking is part of the problem because (I think) they had flats on them to hold in the chuck better? Didn't they?

Thank you in advance.

Re: Silly question of the week... eggbeater drill

#2

Tightening hand drill

Warren in Lancaster, PA

I hold the main handle of the drill in my right hand and curl my right index finger around the crank handle to hold it tight. Left hand for the chuck. For the tightest, hold tight to the chuck, turn the crank handle away from the main handle about 30 degrees and pull back with first two fingers.

Re: Silly question of the week... eggbeater drill

#3

Re: Silly question of the week... eggbeater drill

Wiley Horne--So. Calif.

Hi Joe and all,

Dunno how to help with the main problem you identified--how to operate without a third hand. However, as a Millers Falls tool owner, you have a valuable resource in Randy Roeder's OldToolHeaven website:

http://oldtoolheaven.com/hand_drills/Featured.htm

In this link, he notes that the eggbeaters were shipped with 'traditional drill points', which are illustrated in a separate link from this page, but that the hollow handles were sized to accept the longer twist drills. So the MF design was not limited in any way to drill points.

Also, the drill points shown from this page do not appear to have flats milled into their ends, as did the North Bros. (Yankee) drill points.

Wiley

Re: Silly question of the week... eggbeater drill

#4

What I do

Bill Tindall, E.Tn.

I use this kind of drill so much that it stays within reach of the bench......along with a set of number drills to go in it.

With drill upside down vertical, hold drill bit and chuck in left hand. Crank the handle to get the bit snug. Now hold the chuck with left hand and the handle at 90 degree to vertical with the right hand. Raise the drill and smack the end on the bench. Some combination of inertia and the right hand pressing the gears to tighten the chuck will result in a firm grip. If it doesn't something is amiss with the chuck. My bits (up to 1/4") never slip.

Re: Silly question of the week... eggbeater drill

#5

Jack Guzman from Maine

Re: Silly question of the week... eggbeater drill

Jack Guzman from Maine

Once you get the tightening down pat I got another tip for you. These drills are plentiful for cheap ,at least in my little corner of the world. I keep a rack of them hanging nearby with common drill sizes already chucked in.So ,instead of picking my bit size and chuck it up I grab the drill that has the right size already in it.Years ago that might have been unusual and impractical but nowadays it makes perfect sense.---Jack

Re: Silly question of the week... eggbeater drill

#6

Variant

Bill Houghton, Sebastopol, CA

After getting the bit hand tight in the chuck:

I kind of cradle the drill in my elbow - lay it along your forearm with the chuck at your hand, then bend your arm up, so it's resting along your vertical forearm. Grip chuck firmly and pull the crank handle in the direction that will cause the chuck to tighten. Works best if the pull is also vertical, but down. Watch that you don't get flesh or shirt caught in the works.

Re: Silly question of the week... eggbeater drill

#7

PS untightening

Bill Tindall, E.Tn.

BTW, I loosen the same way. Grab chuck in one hand, handle in the other and thump the top of the drill on the bench while pushing down on the crank handle.

Re: Silly question of the week... eggbeater drill

#8

Re: Variant

Warren in Lancaster, PA

I think that sounds a bit clumsy, Bill. With my method, I can pick up the drill, remove the bit and secure another bit, all in five seconds.

Re: Silly question of the week... eggbeater drill

#9

Re: The right way

TomD

I think I do it mostly like Warren. I wrap my thumb around the fixed handle and grasp the moving handle with my fingers (the moving handle is large so several of my fingers can hold on, not that it matters). Then I take an overhand grip with my right hand, and tighten the chuck. The left hand grip is a bit like holding a brake on a bicycle on motorcycle.

However, this is the other side of it. The grip described above does not feel equally powerful when removing the drill bit, because the moving handle is no longer tensioning the fingers, it is trying to move out of the grip to the inside of the hand. So I switch hands. I remove the bit while holding the drill in my right hand, and fix a bit while holding the drill in my left hand. If you try it, you may well agree it is the right way.

Re: Silly question of the week... eggbeater drill

#10

Re: The right way

Warren in Lancaster, PA

If you have to change your grip in the middle of changing bits, you have a clumsy method also. With my method you can tighten and loosen 5 times in 5 seconds.

Re: Silly question of the week... eggbeater drill

#11

Re: Silly question of the week... eggbeater drill

Joe in a Cleveland suburb

Thanks all.

Re: Silly question of the week... eggbeater drill

#12

Re: The right way

TomD

Clumsy is as clumsy does. However you assume one is changing bits. One could insert a bit, use it for the next 4 years, remove it. Will it really clumsy you up somehow to pick it up for loosening with the opposite hand? I would rather the method was mechanically sound than stylish in some irrelevant way. I think the same thing applies when changing bits. Normally (well I hate to say what it might really looks like in my shop), there is some two hand work opening a file, returning a bit, possibly measuring and fitting a new one to the project, etc...

Or it could be picking up the tool bitless (because I actually put it away). Inserting a new bit, doing the job, returning the bit to it's rightful place. One could go on, but it seems unlikely that the hand switch is a big deal. You can even toss the drill from hand to hand like a chef with a knife (some chefs), if looking clumsy is a big deal.

Sooner or later one's wrestler friend (I have one who carried my 16 inch planer out of his truck by himself) will leave the chuck as he last used it, and one will be happy to use the mechanics that work. Around here my wife weighs under 100 I weigh 250...

The point is mechanical efficiency. Like removing a router bit by positioning the wrenches so all one has to do is pinch them together, again like a hand brake. There are some sporting types who enjoy wrenching the chuck with two hands, and flying wrenches, pinched fingers, and dents in the tool's frame but one can always just do it the right way. It really does help, particularly people with some restriction in strength, like arthritis, to make the best use of the ergonomics.

Re: Silly question of the week... eggbeater drill

#13

Re: Silly question of the week... eggbeater drill

William Duffield

I made a minor modification to my eggbeater, so I can operate the chuck with one hand. I replaced the chuck with a geared chuck with a chuck key, attached the key to the end of a motor shaft, and attached the motor to the side of the eggbeater. Now I can open or close the chuck by flipping a switch and pushing a button. I think I'd really have something if I could find a chuck and chuck key with the same gear pattern as the egg beater's crown gear.

Re: Silly question of the week... eggbeater drill

#14

Re: What I do

Joe in a Cleveland suburb

It sounds like you are describing the process of setting an axe head onto a handle. Is my assumption correct?

Thank you.

Re: Silly question of the week... eggbeater drill

#15

"Smack" may have overstated the procedure

Bill Tindall, E.Tn.



Maybe bump is a better quantitative description of the force. After rotating the crank to snug the bit just raise the drill a bit and then force it back down with the crank hand to bump the end on the bench. The momentum of your hand on the crank will set the chuck on the bit.

BTW, 3.4 seconds to install and seat the bit. :)

Re: Silly question of the week... eggbeater drill

#16

Re: "Smack" may have overstated the procedure

TomD

OK that makes sense, could be useful for someone without a lot of hand strength, or for a stuck bit. Obviously not your issue. I was kinda imagining you going at the bench like a battering ram and hitting the handle on the edge, though I guess in the end it is much the same idea, more controled.

I don't see it as being faster, once you have your hands on the drill, any further motion is pretty much surplus time compared to someone who's hands are doing the tightening, though obviously the extra time is fractional. This is going to delight those people who like denting their bench, or those who so hate it if they always cover it with something like masonite. And there is the whole thing about what you hit when on site, not near the trusty bench, the client's dinning room table?

It is pretty obvious that when they designed planes, they intended us to hit them with hammers, some of both the Japanese, and western varieties have surfaces designed for the hit. Probably all do, actually. But in the spirit of calling up Franklin glue company and swallowing the company line on use, does anyone know what we are expected to do with these tools. We all have our methods, but what where they designed to do? If they really felt we needed to be hitting them with or on things, why wouldn't at least the modern ones have keys, or two part chucks. The one I have is a modern German one, and it is just like the old, ones, (except uglier).

Further, for the size range of bits these things use, I use keyed bit in a snap on chuck on my drill driver, a bit like the Yankee push drill, so this kind of chuck isn't really all that useful unless you use a lot of letter drills. Hex shanks should be easy enough for anyone to tighten by hand. Maybe a little lube every decade would help.