New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Grinder

Posts

Grinder

#1

Grinder

Patrick Gibbons

Not hand tools, please pardon me. I have an Asian-made 6" grinder. The wheels are 1/2" wide with no spacers for the spindle; the wheels fit without them. Wanting to change one out with a Norton 1" wide white, cool-running wheel. This wheel comes with multiple spacers. They telescope into each other. The smallest spacer will fit over the threads but not the shank of the spindle. Should I force it over the shank or use the next size spacer, which is a loose fit? I'm wanting to work safely.

Re: Grinder

#2

Long shot

Wiley Horne--So. Calif.

Hi Patrick,

If you force the inner shim, you'll likely get distortion up through the whole sandwich.

I'll just relate a story for what it's worth, and you can decide if it fits your situation. I had a gouge-sharpening wheel, whose mounting hole was 12mm, compared to a Baldor 6" grinder with shaft 1/2" (12.7mm). You could mic these things and find out the real numbers for your case. The 0.7mm difference amounts to almost 1/32" in the diameter, which meant I needed to ream just under 1/64" from the circumference of the wheel mount hole.

Goal: Ream out the shim to 1/2" (in the example). I took my sharpest 1/2" drill bit and--by hand and slowly--reamed out the 12mm diam. wheel. The drill point self-centered in the hole. It had to bite 1/64" from the inner surface of the wheel mounting hole. The key was to keep the thing I was reaming square to the drill. I did this by fixing the drill in a vise, with wooden v-blocks either side to hold it steady. Then wound the wheel onto the drill slowly, keeping it square.

Result: In my case, the inner core that I was drilling was some paper compound, and the wheel was integral, so the drilling did not distort the mounting hole. It worked fine. The hardest part I see in your case, if you were to try to replicate this, would be to keep the shim from distorting during the reaming. And if you kept it in the wheel sandwich, it would likely spin.

Anyway, that's my story. Consider ways to ream out the shim without distorting it.

2 cents.

Wiley

Re: Grinder

#3

Re: Grinder

Jerry Gibbs

I have had trouble with the telescoping spacers. There is enough slop to make the wheel out of round when spinning.

Re: Grinder

#4

Re: Grinder

John in NM

Don't use the next size up, too loose will be a problem.

I might try reaming it out as William suggests, that shouldn't be too hard.

Might try beveling the inside corner first, in case it's a bit of casting flash or something keeping it from sliding on. Also a bit of lube might make the difference you need.

Re: Grinder

#5

Re: Grinder

Richard Darjes

I don't know if you have access to a wood lathe. There is a you tube video by Ernie Conover called "making grinder wheel bushings" where he makes a replacement for your stacked rings out of hardwood that is an exact fit for the wheel and the grinder's shaft. I copied what he did and it worked very well for me. I made a replacement bushing out of walnut.

Re: Grinder

#6

Re: Grinder

Patrick Gibbons

Just the advice I was looking for. Thank you all.

Re: Grinder

#7

Re: Grinder *LINK*

Patrick Gibbons

Here's the video Richard mentioned.


http://m.youtube.com/watch?v=_7OoqJN2L4Y

Re: Grinder

#8

Re: Grinder

edward in vancouver

I've made bushings for several wheels this way, two of them to fit very skinny 5/16" shafts on hand cranked grinders.

Edward