New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Sharpening a Drawknife

Posts

Re: Sharpening a Drawknife

#2

Re: Sharpening a Drawknife

TomD

That's a good sumary as always, and a useful jig, though I do expect to see it on that show about the many ways to kill oneself. It could probably feature a few times if a person really Darwined out on it.

When picking up tools that may need a referb, or when making them, some means to power grind them is always a bonus. A draw knife is such an ideal candidate for belt sanding, I tend not to move on from there. There is usually some area of slack belt where the convex shapes can be ground, and there is always the platen for regular bevels. At the extreme tools end of the spectrum, there is always this, a rotary platen:


It might at first look like a belt sander, but what it actually is, is a belt tensioned between different pulleys to provide different degrees of deflection. The grinding belt goes over the top of the stuff you see there. Cool, huh, though I don't have one, I just use regular belts.

A minimally practised hand with a draw knife can cut right to the layout lines in a few passes on a windsor spindle. In fact that is the needed technique, as the geometry is a play on cutting to squares, then octagons, then reducing the octagons to squares, in order to get the tapers. With those skills, one shouldn't have much difficulty freehanding the grind. Apparently the student who first spotted the geometry was... a student. So most people shouldn't have much trouble picking it up.

Re: Sharpening a Drawknife

#3

Ellis Walentine

Back bevel

Ellis Walentine

Nice presentation, Derek. I'm remindeed of discussions with Mike Dunbar, who prefers to put a back bevel on his drawknives. I notice that Curtis, at the tail end of Part 2, mentions dubbing the flat side over just a tiny bit using a leather strop with some green compound. As I recall, Mike's back bevel was more dramatic than that.

I'm wondering if you have compared the control issues, especially when making concave cuts, between a flat back and a slightly beveled one?

Ellis

Re: Sharpening a Drawknife

#4

Re: Back bevel

Derek Cohen (in Perth, Australia)

Hi Ellis

I am aware that a backbevel is favoured by some. While my pictorial follows Curtis' method as closely as it could, earlier on I had sharpened the drawknife I have had in my possession for about 10 years, and used at odd times, this being an 8" folding Jennings. This has a slightly rounded back, which I kept. As you say, it will be interesting to compare drawknives with flat and rounded backs.

At this time I do not know enough about these subtleties. I did follow a video where Brian Boggs talked about the variations, and simply stated that there was no correct way, just preferences to suit different situations.

Regards from Perth

Derek

Re: Sharpening a Drawknife

#5

Re: Sharpening a Drawknife

Derek Cohen (in Perth, Australia)

Hi Tom

That is a cool belt sander. Why not build one?

I have something vaguely similar, although it has not seen use in many years. This is the WASP sander, an Australian tool, which is powered by a drill press. There is an optional platten that can be added when sharpening. I guess you'd use it without the platten.


Regards from Perth

Derek

Re: Sharpening a Drawknife

#6

Re: Sharpening a Drawknife

TomD

Cool Derek, I haven't seen one of those before. I have a beaumont 2x72 sander that I didn't build which is a bit of an embarrassment. I didn't think I could tap the heavy/deep steel easily enough, which I later found wasn't a problem, plus I later took up welding. The Beaumont was designed by makers to be home makable.

It is possible to make one of those grinder heads, but if you make all the parts you have to make multiple bearing wheels, which is time consuming, and you have to have a source for the belting which is basically a bandsaw type tire, but made of something that doesn't stretch. Probably Beaumont sells them. Looks like a fair amount of trouble. The basic grinder does most of what I want. It would be worth it to a maker of such things or a knifemaker of convex grinds. The belts will normally follow the "platen" of the axe or drawknife, but establishng the perfect grind in the first place is another mater. Though one they have been doing for years without such tools.

Re: Sharpening a Drawknife

#7

Ellis Walentine

Re: Back bevel

Ellis Walentine

Yeah, I agree with Boggs. Ultimately it is what works for you. But, as Ian Agrell once told me, the back bevel -- or rounded back bevel as the case may be, in his case on carving chisels -- is what allows you the ability to follow inside radii without digging in, as you are able to manipulate your fulcrum point wherever you need it. That would be an added skill dimension to using the tool.

Ellis