New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

L-N Corner Chisels

Posts

L-N Corner Chisels

#1

L-N Corner Chisels

James Blandford-Baker

Just ordered a LN 6.3mm corner chisel as I need to find a convenient way of creating 10mm square mortices in a set of oak dining chairs (10 needed in each chair for top and bottom of the five slats in the back). Plan is to drill 10mm holes and then square them off. Just wondered if anyone knows how much work is generally required in flattening backs of these chisels and if you have any tips on sharpening them which I suspect are a bit tricky.

Thanks

James

Re: L-N Corner Chisels

#2

A thought

Wiley Horne--So. Calif.

This reminds me of the problem of making perfectly square holes for Greene & Greene ebony plugs. I used mortise machine chisels, removing the interior drill and hammering them in. It worked great, and I noticed later Lee Valley came out a little later with a set of square hole punches.

I realize you've already ordered the LN chisel. However, if you want to be 'one and done' rather than square 4 corners per hole, pick a 3/8" or 10mm mortise machine chisel (however they come in the UK), and use the next smallest drill size to clear the way for the chisel.

2 cents.

Wiley

Re: L-N Corner Chisels

#3

Re: L-N Corner Chisels

Patrick Gibbons

I know it's too late now but another alternative would have been to drill holes in the rails and the slats and use dowels to secure the pieces together.

The LN chisels should sharpen easily. The inside bevels can be done with slips and abrasive papers on a hard piece of wood. EZ Lap makes diamond paddles and smaller stones that will work. 3M abrasive films are good. Other solutions are also available.

Re: L-N Corner Chisels

#4

Re: L-N Corner Chisels

Derek Cohen (in Perth, Australia)

Hi James

Wiley's recommendation for the LV square mortice chisels is a good one. I can't say much more since I've not used them, but they make sense.


I have used corner chisels, and find them a royal pain in the watsit. Sorry. Personally, I would not recommend such a chisel. They are very difficult to sharpen. Slips and sides of stones are what you have. If an edge chips and you have to grind it back, then you have two sides to grind, to get them the same height, and to get the bevels at a reasonable angle. I gave up.

LN have a video on sharpening it here: http://www.youtube.com/watch?v=Jo0IXn0pSic

What I have done to date is use a couple of chisels (1/4" and 3/8") I ground from a HSS bar. They look like sash mortice chisels. The parallel sides make it easier to line up.


I do think that the LV chisels are the way to go.

Regards from Perth

Derek

Re: L-N Corner Chisels

#5

Re: L-N Corner Chisels

James Blandford-Baker

Many thanks for all these helpful responses. I am not sure if the LV square chisels are available in the UK yet but I'll check. The alternative of a metric mortice chisel as used on a morticing machine sounds like a possibility if the LVs aren't available.

I will, now I've bought it, give the LN corner chisel a try and let you know how it goes.

Thanks so much

James

Re: L-N Corner Chisels

#6

Re: L-N Corner Chisels

TomD

I have a mortising machine, but there are lot of places where it won't get into. I have a Japanese corner chisel, and I don't use it much, but it seems pretty easy to use. The thing I find is that it it can be as difficult to link up for a smooth circumference as anything else. The hand tool option I prefer is to just cut a mortise. Mortises can be cut very cleanly if one sticks to working cross grain, but it isn't going to be as fast as something like the LV chisel if you only need to go deeply enough for a cosmetic transition.