New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Brace and Bit Recommendation

Posts

Brace and Bit Recommendation

#1

Brace and Bit Recommendation

JDK

I've decided to purchase a brace (braces?) and an auger bit set. I'm looking for something of quality that will last, and auger bits that will hold an edge. I would really appreciate some recommendations.

Thanks much in advance...

Re: Brace and Bit Recommendation

#2

Re: Brace and Bit Recommendation

Kevin French

Braces are cheap you can pick them up for $5 at Flea Markets and Yard sales. This is one area that's fun to figure out what works best. Get some direct drives with different swings, pick up a couple ratchet drives. Get a collection of them and fit them with counter sinks, screwdriver tips... make a rack for them.

Re: Brace and Bit Recommendation

#3

Re: Brace and Bit Recommendation

Patrick Gibbons

There were so many good braces made in this country. Millers Falls, Yankee, Pexto, Stanley and Craftsman-branded braces by the same companies are the easiest to find. The best braces are really overkill for most situations. Top-of-the-line included a ratchet head, universal jaws, ball bearing pad, rosewood, nickeled finish and other benefits. 10" sweeps are most common. 12" and 14" sweeps provide even more torque. 8" sweeps were popular for fastening and removing screws. Russell Jennings and Irwin bits were great and available in fine, med and course threads. Also Swan, Greenlee, and others made great bits. There were bits made for multiple purposes. Go to the Millers Falls page and you'll get a good education on braces.

http://oldtoolheaven.com/brace/brace.htm

Re: Brace and Bit Recommendation

#5

Re: Brace and Bit Recommendation

Patrick Gibbons

I use a brace more for installing and removing screws rather than making holes. For that reason universal jaws are preferred. I'd get an MF Lion brace, Pexto Sampson, Yankee or Stanley 813. All top braces.

Re: Brace and Bit Recommendation

#6

Re: Brace and Bit Recommendation

JDK

Thanks Patrick. Great info.

I think to start I'll get one of those two (2100,2101) Stanleys he recommended, and after going to Millars Falls pick a bit set that meets my current needs.

I'm going to drill round dog holes through the center of my 4' (LN) workbench top so I can get some hold-downs. I'll start them with a 3/4" spiral upcut bit in my router, and finish them off with the brace and bit.

Re: Brace and Bit Recommendation

#7

Re: Brace and Bit Recommendation

Paul in NJ

Most any brace you find at a flea market, antique store, or Ebay will be adequate and work. It comes down to personal preference, ratchet or non-ratchet, and how nice you want it to look. My preference is a non-ratcheting brace. They are lighter and there is no play in the jaws/head. If I really need a ratcheting brace the North Bros-Yankee -Stanley 2100 & 2101 are the best in my opinion. They have the least amount of play and have the tightest and smoothest ratchet. They are heavy.

When it comes to bits there are two common styles, the Jennings and Irwin. There are others that have some advantages but they are much harder to find. I prefer the Russell Jennings with the fine thread lead screw. I have no problems drilling my hard maple bench top for holdfasts with them. I would be leary buying these on Ebay unless you have good pictures. You want to see that the cutting spurs and lips are intact or maintained correctly. Buy your bits in person or from a reputable tool dealer.

One last thing: Buy an auger bit file to sharpen them properly.

Paul Dzioba

Re: Brace and Bit Recommendation

#8

Brace and bit will do all of that

Simon St.Laurent - Dryden, NY

I just put a holdfast hole through my similar bench a few weeks ago. No router needed - an old brace and an Irwin 3/4" bit (oldish stock, but new) did the job easily.

Thanks,

Simon

Re: Brace and Bit Recommendation

#9

Re: Brace and bit will do all of that

JDK

I'm a bit nervous of doing it freehand given my total lack of experience with a brace and bit. That's why I plan to start the hole with the router.

BTW, did you turn the bench over to finish the hole, or did you drill it from underneath? (I presume this is necessary to eliminate tear-out).

Re: Brace and Bit Recommendation

#10

Re: Brace and bit will do all of that

Simon St.Laurent - Dryden, NY

I just drilled it from the top down. It was slow, but I wasn't worried about tearout on the bottom of the bench. I don't seem to have created much. New auger, nicely sharp, went through the hard maple cleanly.

Thanks,

Simon

Re: Brace and Bit Recommendation

#11

Keeping a bit vertical

Bill Houghton, Sebastopol, CA

One of the classic methods for keeping a bit vertical - which I presume was one of your concerns about boring freehand - is to establish verticals at 90 degrees from each other, and sight off those. Two try/combination squares, or known verticals in your shop (like a doorway) that are in line of sight - that kind of thing. You then sight along the bit as you bore.

Because auger bits are self-guiding once the hole is established, you need to do that only until you're some distance into the wood.

Re: Brace and Bit Recommendation

#13

Re: Keeping a bit vertical

Patrick Gibbons

If you can find a bit with a fine thread, it will work better in hard wood. It pulls the bit into the wood such that a finer shaving is taken from the cut. This reduces tear out and produces a cleaner hole as well as making it easier to rotate the brace. If you watch your shaving as it's being produced, you'll notice if it is heavier or lighter on one side. This indicates you're off square. With a brace, you can go slowly enough to correct your position as necessary. A drilling guide is also easily made.

Re: Brace and Bit Recommendation

#14

I'll confess

Simon St.Laurent - Dryden, NY

That I drilled the holdfast hole freehand, with just a square next to the bit to give me a rough idea. Not a great plan for more involved projects, but worked fine for this one!

Thanks,

Simon

Re: Brace and Bit Recommendation

#15

Re: Brace and Bit Recommendation

Tony Wilkins

I have a couple of braces that I've used for the last year. One is an 8" Bell System and the other is a 12" Fray Spofford-bit.

The only time I use the Bell is when I need the extra-speed of the smaller throw or I need to use a modern round drill bit.

I love the simplicity or the Spofford brace.

Good suggestion on the auger bit file to touch them up.

I used the spofford and a 3/4" Irwin to drill my hold fast holes in 2" Maple top.

Re: Brace and Bit Recommendation

#16

Re: Brace and Bit Recommendation

David Churnega

This is the most bang for anybody's buck and I am selling.


img

Re: Brace and Bit Recommendation

#17

Re: Brace and Bit Recommendation

JDK

Do you have a photo? It isn't in the post.

Re: Brace and Bit Recommendation

#18

Re: Brace and Bit Recommendation

David Churnega

I sometimes have a problem with pictures here. Send an email address and I will send picture.

David

440-345-5074