New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Wm. Marples Spokeshave Question

Posts

Wm. Marples Spokeshave Question

#1

Wm. Marples Spokeshave Question

Patrick Gibbons

Acquired the spokeshave shown. A delicate little boxwood, low angle shave made by Marples. It is a round spokeshave and appears to have hardly been used at all. The blade has never been sharpened and is concave on the bottom. Shouldn't it be flat? I got this with a box of leather working tools. How do I remove the blade from the body without ruining the wood? Any other tips would be appreciated.


img

Re: Wm. Marples Spokeshave Question

#2

Re: Wm. Marples Spokeshave Question another image 


img

Re: Wm. Marples Spokeshave Question

#3

Re: Wm. Marples Spokeshave Question another image 


img

Re: Wm. Marples Spokeshave Question

#4

Re: Wm. Marples Spokeshave Question *LINK*

Patrick Gibbons

From the 1938 Marples catalog on p.68 it appears to be a patternmaker's shave.


http://toolemera.com/bkpdf/MarplesCat1938.pdf

Re: Wm. Marples Spokeshave Question

#5

Re: Wm. Marples Spokeshave Question

Paul in NJ

Hi Patrick,

nice spoke shave. The back is ground hollow to allow easier sharpening, there is less metal to remove. It is important that you keep the back flat on the stone and do the minimum to get a shiny edge. No stropping! Most of the honing should be done on the bevel side. A back bevel or dubbing the back edge is death to cutting action because there is only a small clearance angle. You remove the blade by tapping the tangs on the opposite side. The blade is a friction fit. Adjust the blade by tapping the blade on your bench or with a small hammer. Tap the tangs to increase the cut or tap the back of the blade to decrease. Have fun, these are great tools and I never pass one up that is in good shape.

Paul Dzioba

Re: Wm. Marples Spokeshave Question

#6

Paul, a question

Patrick Gibbons

You say no stropping. Could you tell me a little more how you go about sharpening this blade. Also, I tried using a hammer to tap out the blade. It moved, but it's very tight. I suppose that's better than too loose.

Re: Wm. Marples Spokeshave Question

#7

Re: Paul, a question

Patrick Gibbons

I spoke too soon. Got the blade out to find some abuse. The bevel's been roughly ground and sharpened like a knife blade. A very slight back bevel.

Re: Wm. Marples Spokeshave Question

#8

Re: Paul, a question

Larry Barrett

Patrick, have you tried the shave on a stick to see how well it works, and if it needs sharpening? The steeper 'microbevel' may work just fine.

One neat thing you can do with this type of shave is set one side of the blade a little ranker than the other side. You do this by tapping the tang a little deeper on one side than the other. If you are shaving something like a chair rung, you can get a heavy or light shaving just by sliding the shave one way or the other. A real time saver.

Re: Wm. Marples Spokeshave Question

#9

Re: Paul, a question

Patrick Gibbons

I tried it on a piece of pecan and it is quite blunt. Even so, it still took a shaving.

On another note; I read a blog entry on the net written by Mike Dunbar where he was highly critical of this shave owing to its round front edge (rather than flat). It will be interesting to see how well it performs once it is tuned up.

Re: Wm. Marples Spokeshave Question

#10

Re: Paul, a question

Paul in NJ

Hi Patrick,

I have some small rectangular slip stones that I hone with. First I clamp the blade by both tangs in my metal vise. I place the stone perpendicular across the blade and rub it back and forth. I say perpendicular because it helps keep me from rocking the stone and dubbing the edge. Next I turn the blade over and clamp one tang in the side of the vise to give me access to the bevel. I hone the same way, the stone perpendicular to the blade. I have hollow ground the bevel on my grinder freehand but it takes a steady hand and is easy to mess up. I imagine you might fasten the blade to a stick (maybe as simple as using baling wire) and be able to use the rest on your grinder. Like I said before, I try to buy shaves in good shape. I think Mike Dunbar in his book on restoring tools might have some sharpening info.

I don't know of any jigs to do this.

Paul Dzioba

Re: Wm. Marples Spokeshave Question

#11

Re: Paul, a question

Patrick Gibbons

Thanks. Sounds straight forward.