New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Question for the plane experts

Posts

Question for the plane experts

#1

Question for the plane experts

Edward in Vancouver

Picked up a rabbet pane at the flea the other weekend, still trying to figure it out.

It's 3/4" wide and home made. The maker made the stock in two pieces, the first was and "L" shape, then he excavated for the iron, the he glued on teh second part, and then he bolted on a steel sole. The iron is home made from an old file.

The toe, which is also steel-clad, is a good 1/8" higher than the rest of the sole, when I show the bottom of the plane to a known flat surface, the toe is a good 1/8' higher than the rest of the sole.

The plane can be described as "work-a-day", not butt-ugly, but the owner did not bother with and fancy work. It is obvious that the owner had spent some time fitting the steel sole to the stock, shaped the wedge,and took some time to grind and shape the iron from an old file.

Can't figure out why the toe is higher than the rest of the sole, and I can't make a decent rabbet with it either...

Any suggestions?

Re: Question for the plane experts

#2

Re: Question for the plane experts

Bill Houghton, Sebastopol, CA

The toe on the Stanley 75 bullnose plane is higher than the sole, too, but by a little, not by any 1/8". That much difference would all but require that any cut be at least 1/8", one heck of a bite. Puzzling.

Oh, and the Stanley 75 doesn't work terribly well, in my experience at least, either.

Re: Question for the plane experts

#3

Re: Question for the plane experts

Rob Lee

Hi -

Sound to me like this is made for a single application - and is for a fitting operation.

Don't think of it as a plane (though it sounds "plane-like") - think of it as a registration surface offset 1/8" from the cutting plane of the blade.

A reasonable guess would be for hinge installation - rough out with a chisel, then do the fielding work with this tool. There were carpenters that spent weeks installing doors in office towers, or hotels.... and a purpose made tool could make a real difference.

It could just as likely be for some similar operation in another industry though...

Cheers -

Rob

Re: Question for the plane experts

#4

Re: Question for the plane experts

Edward in Vancouver

Thanks for the responses.

I guess I could cut the plane's stock along the glue line, where it was originally glued together, and remove about 1/8" of wood and then glue it back so the sole is parallel, but then again maybe I should just leave it alone and not mess around with it.

Still, the way it was made is neat, and maybe I'll use that process to make one for myself: On the "L" shaped piece of stock, the mortise for the iron was excavated, and on the glued-on piece, the ramp of about 45 was cut. When glued together, it makes a decent body.

Re: Question for the plane experts

#5

Re: Question for the plane experts

Derek Cohen (in Perth, Australia)

I have nothing to offer but just want to say that I find these topics fascinating - sort of "forensic archeological woodworking". Rob, I think your re-construction is brilliant! Not sure it is the only explanation, but it fits.

Regards from Perth

Derek

Re: Question for the plane experts

#6

Additive vs subtractive woodworking

Bill Houghton, Sebastopol, CA

Why not add a 1/8" shim to the front first? That's reversible, if you find it's not helpful.

Re: Question for the plane experts

#7

Please post a picture.


Re: Question for the plane experts

#8

Re: Doh!

Edward in Vancouver

Well, uh...yeah, glueing or taping on a shim to the toe would make a lot of sense, actually, a whole lot of sense.... Doh!!! Why didn't I think of that?....