New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

The Chair - Arm/Backrest Joint (pt 1)

Posts

Re: The Chair - Arm/Backrest Joint (pt 1)

#2

plywood

Lars Parrington

Within the finger joint, the grain direction of the two pieces (arm and backrest) are perpendicular to one another. In that way the joint area is similar to a piece of plywood, and to an extent, this allows each piece to reinforce the short grain of the other piece. Thus if a failure occurs, I'd expect it to be in the short grain at a point just outside the joint area. Perhaps by making the joint deeper (fingers longer), enough of the shortest grain could be reinforced. You also might consider using slimmer fingers in the joint (and more of them) to increase the strengthening effect.

Another option for strengthening the grain in those areas would be to cut some kerfs through them, and glue in spline pieces with the desired grain orientation. This would probably be best done before cutting the finger joint.

Both of these ideas would affect the final appearance of the joint, so you have to decide if and how much you are willing to compromize the appearance for the sake of strength.

Re: The Chair - Arm/Backrest Joint (pt 1)

#3

Re: The Chair - Arm/Backrest Joint (pt 1)

Larry Barrett

Regarding "points vs round", while either is clearly difficult, if you were to drill in from both sides it would seem to me that a round joint could be accomplished as "easily' as a point joint. Any error would be transferred to the interior, and if error existed, epoxy might be the answer. You are brave to tackle this without practice. Were I you, and if I had actually gotten this far, I would have tried the joint in some scrap first.

Excellent work so far. Thanks for sharing it all with us.

Re: The Chair - Arm/Backrest Joint (pt 1)

#4

Re: The Chair - Arm/Backrest Joint (pt 1)

Bruce McCrory

I would roll and blunt, to nearly vertical, the first dagger (finger) of the back top; and possibly the bottom, where they surface. Otherwise you could potentially have a long run out of grain and glue and even spelching of the finger tip.

Re: The Chair - Arm/Backrest Joint (pt 1)

#5

Ellis Walentine

A couple comments

Ellis Walentine

First, that wood is splendid, Derek. I can already imagine how wonderful it will look when you're done.

Second, I would try to preserve the rounded points on the finger joints (no rhyme intended), primarily to preserve the look of the original. There are a few things that I regard as inalterable, one of which is a design detail in a reproduction of a classic piece. You may have the best intentions and the most well-rationalized reasons for taking liberties with it, but it isn't your design. An informed viewer will see -- consciously or unconsciously -- that there's something different about this joint with the pointy fingers, and the overall effect will be diminished. Sorry, that's my feeling on this matter.

Making those rounded sockets should be pretty easy, without resorting to drilling. You can saw down to the diameter of the 3/16" round and take out the rest with a chainsaw file.

Your technique of preparing the stock for marking out is really the only way to do it. Good call. It all harks back to the original premise of having the three pieces flat and level with each other, which would have been required in any event for a shaping operation, although I suspect they kept the stock at full rectilinear size for shaping. That way, any tearout would be in the waste areas of the blanks.

Looks like a downhill glide from here, Derek. Keep us informed.

Ellis

Re: The Chair - Arm/Backrest Joint (pt 1)

#6

Re: A couple comments

Tom in Toronto

"Second, I would try to preserve the rounded points on the finger joints (no rhyme intended), primarily to preserve the look of the original. There are a few things that I regard as inalterable, one of which is a design detail in a reproduction of a classic piece. You may have the best intentions and the most well-rationalized reasons for taking liberties with it, but it isn't your design. An informed viewer will see -- consciously or unconsciously -- that there's something different about this joint with the pointy fingers, and the overall effect will be diminished. Sorry, that's my feeling on this matter."

Having argued both sides of this question already, I think I came out on the side of sticking with the original, in part because it would be fun to make a rounded float...

On the repro thing, the logic dictates as you say, I suppose. Against that are a few things. 1) One is the idea that Derek is making a strong statement about this thing being made by hand, which at least to this audience is a major theme he has, and from a certain perspective this is the logical joint to make that statement. of course like a bad tattoo he will have that satisfaction only for a while, and have to live with the rest of it for ever 2) There is always the possibility they got it wrong. From what I can see there are several structural flaws in their approach. You would be a better judge than I, but is it really the case that people always repeat signature flaws? I thought a lot of repro work often corrects the master. So at some level it might depend on whether one thinks they saw any joint at this point, and the joint they chose as a sginature (krenove exposed dovetails), or something that they would have hiden had they been able. There are construction and aesthetic shortcuts in this piece that are like a 2x4 across the bridge of the nose. 3)

"Making those rounded sockets should be pretty easy, without resorting to drilling. You can saw down to the diameter of the 3/16" round and take out the rest with a chainsaw file."

I have might doubts in both directions. For this joint to come off, and be strong, is has to be melted together. That is less easy, particularly given the difficulty of the layout. The rounded ends aren't going anywhere, and if there is anything about the shape or length that is the least off it will be very noticeable. On the other hand, the points are also a problem, or might be, as they can penetrate even split each other, for much the same kind of reason. Because of the slope, there is a multiplier effect whereby a small eror around a pencil line is a much bigger depth error.

Anyway, I imagine at the rate he works, Derek already has made whichever cuts.

Re: The Chair - Arm/Backrest Joint (pt 1)

#7

Ellis Walentine

Re: A couple comments

Ellis Walentine

Against that are a few things. 1) One is the idea that Derek is making a strong statement about this thing being made by hand, which at least to this audience is a major theme he has, and from a certain perspective this is the logical joint to make that statement.

I don't think the statement needs to be made at the expense of the original aesthetic. The actual cutting of the joint wouldn't be significantly different if he decided to keep the rounded detail and it wouldn't be inferior structurally.

There is always the possibility they got it wrong. ... is it really the case that people always repeat signature flaws? I thought a lot of repro work often corrects the master.

I'm not saying it isn't so, but I disagree with the notion of "correcting" the master. I think you do a reproduction for a reason, as an homage to a master, not to make a statement or to improve on the master's design. The Chair has been called the most beautiful chair in the world and has been in production for over 60 years, aesthetic and construction quibbles aside.

Just my two cents. Of course everyone is entitled to their views.

Cheers,

Ellis

Re: The Chair - Arm/Backrest Joint (pt 1)

#8

Re: Well...

Tom in Toronto

The other side of that, which we got into at the outset is the whole issue of copying, and forgery. Particularly with ancient furniture, there is a whole scholarship to determining what the authentic style of a piece was. Studying the various examples that have survived for some reason, and then producing a copy that is as perfect a representation of the piece as scholarship and craftsmanship allows. But if you have a perfect example off ebay, or whatever, and you slavishly reproduce it in every respect (obviously not species of wood in Derek's case), and the piece is made today under license, and there is the possibility of the example and copy being in the estate at some time (I forget whether Derek owns the example or borrowed it), you are possibly, no mater how pure the intent in a different area.

So I guess it is a mater of what the heck the maker wants. Does he want to do an homage, not exactly that I heard; Does he want to do it all with hand tools, could require adherence or divergence from slavish copying; Does he want to improve the breed, and if so can any improvements be actually visible; Does he want to avoid slavish copying of a trademark piece.

As far as strength it is obviously strong enough if surviving chairs provide any guide, but the emergence of a butt joint at the top of the rail is nasty. The low gluing power of the bullets is nasty, but I don't think it really maters in most failure modes other than straight down on the rail which in practice doesn't seem to be a problem.