We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
They warm up after a little while and are brighter. Still annoying though.
I bought one Cree LED bulb for $12 at Home Depot. Way better than a CFL, only way I know its not an incandescent is it's not as hot to the touch and I still feel a distinct lightness of the wallet
CFLs have been terrible from the outset. For one thing the stated replacement values often are a lot lighter so your stated replacement size for a 60 might be something like 52 w. Then it is like a 25 or worse. It made me think that the purpose of the haircut was just to cover extreme low performance of these bulbs. Who is clamoring for weaker bulbs in any case.
Anyway LEDs are coming on nicely with better prices and performance.
I don, t know what the deal is but normal fluro can through strobe effect make motorized cutters seem to be not moving. What about CFLs or LEDs.
The 100W equivalent CFLs that I've bought are just as bright as 100W incandescent lights.
However I hate CFLs. They are expensive, they burn out just as often as an incandescents, and they are hard to dispose of. Some of them have a noticeable start-up delay, and some are dim for several minutes until they warm up. Some of the 100W equivalent CFLs are too large to fit into the housing where a 100W incandescent used to fit.
I've stocked up on incandenscents and am waiting for LED technologies to advance and LED prices to decrease. Skip the CFLs.
I've never seen a fluorescent do that strobe thing, I think I recall that it has to do with line voltage fluctuations. In theory CFL's could do the same, but I doubt it would be a problem with LED's. Maybe, but I doubt it.
Chalk up short life to cheap Chinese imports. Someone is sucking your money. Trouble with LEDs: Same thing. Crappy Chinese junk! We should be hearing the mortality woes soon.
I still have incandescent replacements (CFL) from ten years ago. They were made in USA. Then the bean counters started adding up the losses. It's now called "sustainability". Rape the environment, rape people to sustain shareholder profits.
I guess I've been lucky. Most of mine have been a little brighter than the incans I replaced. I started several years ago as my originals burned out. The builder used commercial grade bulbs and they lasted over ten years in most cases. oredered the initial bulbs online before HD and Lowes had many of them. Never had any issues with them. I bought an LED bulb at HD (they sell the CREE bulbs) and it has been working real well. I stuck a couple of leftover CFLs in my shop lights (on arms) and they have been great. I really appreciate that they don't get near as hot as the old bulbs. My wife is an artist and she needs lots of good quality light. We outfitted her studio with the high end CFLs that are "true" color rendering, blah blah blah. They made a big difference. Her studio is very bright and the color difference is obvious. I think like anything, there is a large variance of quality in the CFL's. As a nerd/geek, I'm interested in LED's these days. I installed the Lee Valley strip led's in our kitchen and used the leftovers in my shop under a shelf over my bench. hat made a bigger difference than I thought it would.
Some bulbs are better than others in terms of instant brightness. When you find bulbs that are good, stick with that type.
For 7 years, I've had two 100W replacements in my garage, and neither have burned out, but it's a cold area in the house and they do take some time to warm up. I have T12 fixtures in the garage, too, so they aren't really doing too much at this point.
I've also used 13W bulbs all over the house and find them to last as long as they say they're supposed to. The bulbs in my outdoor post light (which are never turned off) last about 2 times as long as the ratings - they are in an area that is generally cool and they never get turned off - it's ideal for them.
I gave all of my incandescents to my dad. He never turns lights on unless he's using them that instant, and the room where he works has had flourescent tubes as long as I can remember, so it makes little difference what bulbs he uses and incandescents really please him. He'll have the last pile of incandescents I gave him until he dies, i'm pretty sure. He and my mother had an addition put on the house almost 20 years ago, and the incandescent fixtures still have their original bulbs. He gets defensive if I start asking details about why bulbs have never been changed, etc, and I can tell when we visit and leave a light on, that it grates on him. He grew up poor. He's loaded now, but he'll never be able to leave the mentality behind (e.g. he still turns the water off while he takes a shower, and he's on a well, so there's very little cost to it).
Anyway, there's always a learning curve with everything. Some bulbs are better than others. If I get a type that takes forever to come on and takes forever to brighten, I don't buy them a second time. That's left me with a house full of CFLs that I really don't mind. The way my wife will have a dozen fixtures on in the house, I can't really afford not to have CFLs.
Don't know what you should be using, but I can tell you my story. Our house has can lights pretty much everywhere. They were outfitted with incandescents when we moved in (Jan). That August my electric bill hit close to $500 (hot summer.) I hit a mistake sale at HD and bought enough CFLs to replace all the incandescents in the house. Electric bill has dropped by about $200 with no other changes. I've put LEDs in a couple spots where we need instant on or leave the light going all night. I'll move to the "better" LEDs slowly, as the CFLs fail. The slow warmup really bugs me.
I don't understand the need for instant gratification on startup brightness. My glue pot isn't instantly up to temperature. My SawStop takes most of a minute to run through its safety checks. When I come into the shop, I need to take time to set down my tool tote and axe. I need to connect my iPad to my MP3 player, pick some music and adjust the volume. I need to turn on the radiant heater. Usually [no, always], I need to put away a few tools and gather my thoughts before I pick up where I left off with the detailed work that requires really bright lights. It'll take a bit longer tomorrow morning, because tonight's forecast is for a low of 2° F, but I'll be thankful next summer for the decreased radiant heat thrown off.
I have modified most of the T12 Fluorescent fixtures in my shop to accept CFL bulbs instead, so I no longer need to worry about the old ballasts, and when Cree LEDs come down a bit more in price, I will just unscrew the CFLs as they burn out and replace them with LEDs.
I also don't understand the issue with color balance. CFLs come in many different color temperatures, and you can mix and match them until they are just what you want. They still won't exactly match each and every lighting condition of every room at all hours of the day where your furniture might live, and anyway the wood, finish, dyes and pigments will change drastically over the life of the piece of furniture. Even if you just throw them in the trash, they will release less Hg, CO2, etc., into the environment than the coal-fired plants generating the electricity to burn the equivalent incandescents.
I think it's completely unethical to continue to use incandescent bulbs. They should all be replaced immediately and recycled, and definitely not given away to reactionaries who will continue this wasteful practice. That's equivalent to giving away our technology, free, to the Chinese, without demanding compensation or improved environmental standards, or improved working conditions.
The complaint with CFL's is that the older and simpler incandescent bulbs worked better and cost less. The dissatisfaction with the new and improved method of lighting is that it is not an improvement from the point of view of those upon whom it has been forced.
It's going to be obvious, so I'll just say it -- I find the preaching to be a bit irritating, especially since I do not find it to be based on an understanding of energy use and inefficiencies. While I do not doubt that you are capable of understanding these things, I do not think you have bothered to observe and think much about it.
By way of example, how much power does an AC unit use compared to a house full of 100W incandescent bulbs? Perhaps the moral effort would be better spent on improving insulation standards than demonizing the humble light bulb? I sure think so.
I do not think that people are unreasonable to expect light bulbs that do not require time to warm up. I do find people to be somewhat unreasonable to expect "instant on" appliances like DVD players that sit there 24/7 sucking up a little juice and displaying "standby" on their little screens. Why not criticize that instead of people's preference for a light bulb that is as good as the one they used to have?
personal startup time. I sure don't bounce out of bed, ready to go.
I don't want to fan the debate, but thinking about John's comment, I don't know that it's an either/or matter. Efficient light bulbs, yes; insulation and house design that's less dependent on electricity, yes. Woodworking that doesn't consume lots of electrons, yes .
We've been on a long term program, with our 1895 house, of room by room upgrades, which have included insulation and have also included reworking the layout to get more daylight, reducing our daytime lighting needs. It's made a huge difference not just to our lighting usage but to the livability of the house.
CFLs frustrate me, because the actual lifetime is less than the theoretical lifetime due, I think, mainly to production quality. Some of the other energy-efficient lighting options are much better.
It's not an either/or matter when it comes to saving energy or just the $$$ spent on energy that could instead be spent on more satisfying things or saved for a rainy day.
If CFL's worked as well as older bulbs, there would be little resistance to switching because there would be no practical reason to resist it. Increased price could be quickly rationalized, and if they lived up to the advertised lifespan, it wouldn't even need to be rationalized.
I'm actually quite optimistic about the success of the new LED bulbs, because as far as I've seen, the only downside is the price
If those morons we consistently vote for would also do something about some of the more serious energy sinks, I wouldn't even complain about their forcing me to buy expensive bulbs.
Another thing to consider - if new low wattage bulbs were not required, just offered at a higher price, it is at least possible that there would be some incentive to manufacture them well enough that they would outlast cheaper incandescents by 10x. The current state of affairs virtually guarantees that manufacturers will cut corners to the point where the new bulbs last only as long or not even as long as Eddy's bulb (I'm tired of typing that I word ), yet still cost 3x more.
In my Cafe we have about 40-odd ceiling mounted GU10 halogen lighting fixtures. As they burn out, I've been slowly replacing them with led bulbs, at $15 a bulb, they are pricey, but well worth the investment.
I realized that led bulbs didn't put out heat, but never really appreciated that fact until the day the thermostat in my chocolate display case broke, and I came in one morning to find about $400.00 worth of chocolates frozen and displaying frost damage in the case. Rather than call in a HVAC guy (who charges $80/ hr plus truck fee, plus parts, plus taxes) I sat down and had a good long think...
The case is 6' long and about 30'' deep with 3 shelves, each shelf has a florescent lighting fixture, and I keep the case at about 18 Celcius, or just slightly cooler than room temp. Why on earth do I need a refrigerated showcase? I knew the answer was that the florescent lighting would melt the chocolate, experience backed me up on this, especially as the florescent fixture was less than 4" away from the chocolates. But the lighting was necessary, the chocolates would just be lost in the dark if I didn't have any lighting to show them off.
It was around this time that LV began to carry the led strip lighting, and I remember looking through the monthly flyer at the whole system. For around $150.00 I re did all the lighting in the case, all I need to do was mount the strips on a narrow strip of wood and insert that into the existing fixture and wire it up.
Not only did I save myself a hefty refrigeration repair bill, but I've turned off the case completely. This means far less power consumption as well as far less heat output, and that means less strain on my A/C system in the summer months, and no compressor noise either.....
I'm not a PhD economist, nor do I play one on TV (or the www), and even if I were, the issues of costs of different types of bulbs probably would not be my specialty. Further, I haven't hacked into the website of the Chinese equivalent of the Department of Commerce, so I have no way of knowing what resources go into their production of CFLs or what pollution results. In any case, let's just say my pundits and your pundits disagree
You don't need any of those things that you are not - phd economist or super hacker - to do a little thinking on your own rather than follow the herd that the pundit tells you to.
Same thing, different suit. They peddle poison and swill it.
"Poison" in this instance is bad product at maximum profit. Well, real poison, too. China equals cheap or zero labor costs, and zero environmental protections. There is only one reason for sending work, food processing, and production to China.