New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

A little consumerism

Posts

A little consumerism

#1

A little consumerism

Wiley Horne--So. Calif.

Hi all,

I have what I need these days. And then some. Counting my blessings.

1. But every once in a while some new bug bites. Like today, I was reading Patrick's post down below here somewhere about his ordering some combination square stuff from Harry Epstein. I decided to go look around. And found these:

http://store.harryepstein.com/cp/Sdsets/HG-8.html

Always wanted nice straight slot screwdrivers. Not the wood handles--the blades. Will report further when they arrive.

2. The other tool matter is about the LV groove cutter, here

http://www.leevalley.com/US/Wood/page.aspx?p=69874&cat=1,43314,69873

Today, I tried both the stringing cutter, and the groove maker. I'd still rather bandsaw the strings, and plane them to size--I don't see how it's practical to slice through 1/8" ebony with a knife cutter. But the groove-cutter is sensational. Tool comes with a 32 thousandths cutter (about 1/32"), and you can buy 25 thousandths and 40 thousandths. These cutters are made so that you pull in one direction to score the channel, and then pull back to scoop wood out of the scored channel. It works very easily, and the channel is clean as a whistle. I have been ripping these channels with a Preston-type stringing cutter (basically a square tooth with sharp edges), or a homemade version thereto, and that works fine. But this LV cutter is the best thing yet. And furthermore, all the cutting parts are located right together, and you can see them cut--which means you can work right to the end of the channel, and leave only a short bit of cleanup at the ends. Works well long-grain and cross-grain. This is a terrific groove cutter!

Wiley

Re: A little consumerism

#2

Ellis Walentine

Good testimonials

Ellis Walentine

Those gunsmith screwdrivers are a real bargain. The groove cutter sounds great, too.

Thanks for the tip, Wiley.

Ellis

Re: A little consumerism

#3

Re: A little consumerism

Lloyd Robins

Wiley, I got my Grace's from Epstein, and I really like them. The handles fit my hand pretty well. I love the animation on their shopping cart. Are you planning on turning new handles?

Re: A little consumerism

#4

Re: A little consumerism

Lloyd Robins

Oh, yes - they also have pretty good prices on Osborne dividers if you want to spend some more money. No, I am not affiliated with them, I just like the way that they do business.

Re: A little consumerism

#5

Re: A little consumerism

Wiley Horne--So. Calif.

Lloyd and all,

You're the fellow who introduced me to Epstein's! Thanks!

My post above was written too hastily. I like the handles just fine. But it's the hollow ground, hardened tips I really want.

Wiley

Re: A little consumerism

#6

Re:Master set

Tom

Always wanted this one:

http://www.brownells.com/gunsmith-tools-supplies/general-gunsmith-tools/screwdrivers-sets/fixed-blade-sets/fixed-blade-screwdriver-sets-prod41573.aspx

But at the end of the day I make them out of O1 or drill rod to actual sizes. Apparently a simple method is to get some sets of Allen keys, the long ones, from discount stores, and grind or machine those, as they come adequately heat treated.

Of course there are always these, but I don't like fiddling with them. But it is the only start to a full set.

http://www.brownells.com/gunsmith-tools-supplies/general-gunsmith-tools/screwdrivers-sets/magna-tip-sets/magna-tip-professional-super-set-prod26376.aspx

Re: A little consumerism

#7

Re:Master set

Patrick Gibbons

Lee Valley also has the Grace straight screwdrivers made for cabinet screws available as a set or individually. Epstein's also had Grace handles for little dinero in various sizes. They're already out of a few sizes.

Re: A little consumerism

#8

Re:Master set

William Duffield

Instead of drill rod, why not use HSS drill blanks? They're already hardened. I know it takes a while longer to grind them, but a screwdriver is not a complicated grinding operation, and you save the hardening and tempering step. Also, unlike O1, they're stainless.

Re: A little consumerism

#9

Re:Master set

Wiley Horne--So. Calif.

Hi Patrick,

Thanks for the info about Lee Valley--didn't realize they had them (why didn't I go look??). Oh well, I'll see how I make out with the gunsmith ones. LV's set of 5 straight slots at $32 might have been a better buy, but I'll survive.

Going to LV's display, with the square drives, makes me wonder all over again how Phillips screws got into general use. Designed to cam out, for goodness' sake!

Wiley

Re: A little consumerism

#10

Re: A little consumerism

Brian from Monument

Being a gunsmith myself, most gunsmiths professional and amateur prefer the individual width and thickness selections afforded by the Magna-Tip screwdriver system sets available from Brownells. They are more expensive but each slot thickness and width encountered in a firearm must be matched exactly or the screws get boogered. The bit selection also includes the thin slots so that they can be used in Brownings and many of the European shotguns (which are notorious for having thin slotted screws. Not only that but the tips are hollow ground so they approximate more exactly the rectangular nature of a slotted screw. The normal screwdriver obtained from sears, stanley etc are all shaped like wedges.

Each width and thickness is a bit. There are several handles; magnetic, short, long, ratchet drive, hollow handle for carrying a small set to the range.

Yes I have a set of the grace screwdrivers but I don't use them. I bought them early on.

I do not own stock in nor am I in any way affiliated with Brownells except as a customer.

Re: A little consumerism

#11

Re:Master set

Brian from Monument

I have and use daily the professional super set although I don't deploy all of the handles.

I even had to make a special drawer in my walnut rollaway to store the set in as it was deeper due to some of the longer bits.

For a gunsmith, a set like this is essential to being able to work on any gun encountered.

They are a bit pricey..... ok a lot pricey.

But well worth it.

If I see one of those expensive European shotguns, that set pays for itself in not buggering some guys screws.

Re: A little consumerism

#12

Look at some of the videos on Epstein's page.

Brian from Monument

Go to the home page of Epstein's site and watch some of the videos.

Stuck excavator 2

pretty cool.

Re: A little consumerism

#13

Re: A little consumerism

Jerry Nicholson

I just got a set of the screwdrivers. They look OK but the advertising claims they are hollow ground and they are not - they just have some of the taper ground away near the end so that the ends are square. Serves the same purpose as hollow ground but the advertising is misleading.

Jerry

Re: A little consumerism

#14

Re: A little consumerism--pass on screwdrivers

Wiley Horne--So. Calif.

Hi Jerry and all,

Just got my screwdrivers. Under magnification, the tips are slightly hollowed. For those that haven't seen these, it's just the last 1/8th inch or so that is hollow ground--other than that they look like keystone pattern. And they do get a real good bite in the screw slot, amazing if you've only used the taper ground ones before (like me).

However, I don't recommend these ones from Epstein. As I look under magnification, I see a number of the tips have grinding errors--munged or slightly rounded corners. You should pass, as I should have.

Well, I got what I paid for, and they're better than anything else I have by a good margin. But I--and you, if you want the Grace drivers--would be better to buy the cabinet set from Lee Valley, which undoubtedly will have first quality tips. The tip precision is the whole point of getting them anyway.

Wiley

Re: A little consumerism

#15

Re: A little consumerism--pass on screwdrivers

Jerry Nicholson

I got my set today. The tip grind is similar to what I did to one of my screwdrivers recently to make it fit the sight elevation adjustment on my Springfield Armory 1911 Range Officer. My grind was cruder but useable.

Jerry