New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Back Polishing Problem

Posts

Back Polishing Problem

#1

Back Polishing Problem

Tony Wilkins

I was working on the initial polish of a blue spruce long bladed paring chisel tonight. I didn't make much headway. I couldn't seem to get a polish. I finally figured out by changing directions that I was just putting in more scratches and not failing to remove them - i.e. the scratches were almost instantly replaced with scratches going in the new direction I was moving the chisel. It's A2 steel and I was using my water stones (1,000 grit Hida and 6,000 grit King S3).

So is getting a finer stone the only way I can sharpen this bad boy effectively?

Re: Back Polishing Problem

#2

Re: Back Polishing Problem *LINK*

Bruce, a MN Galoot

try diamond paste on a cast iron plate. I have king stones, 800, 1500 and 6000 and they don't impress my LV A2 plane blades at all. The diamond on cast iron made very short work of it. Either do a search on WC or read this article by Bill Tindall and Phil Smith:


Loose Diamond Sharpening

Re: Back Polishing Problem

#3

Re: Back Polishing Problem

Derek Cohen (in Perth, Australia)

Tony

A couple of points:

Firstly, it is not necessary to polish the entire back of a blade. The back only needs to be coplanar, that is, flat at the end-middle-end points. The only area that needs to be polished is immediately behind the bevel face. 1/2" is sufficient ... indeed, 1mm is sufficient.

Secondly, consider that a mirror reflects most light. The better the quality of the surface, the more light is reflected. Substitute "smoother" for "better" and you begin to get what is on the rear of a blade. Random scratches are evident as they disturb the smooth flow. Increase the number of scratches and the mirror becomes matt. Some stones are known to be better or worse at creating polish - i.e. are purer in their construction.

It is not just that the 6000 grit is not smooth enough, but it may not be "pure" enough - it no doubt contains more random larger bits of grit than a higher rated stone. Alternately, the larger scratches you refer to may simply have been transported from the 1000 to the 6000 stone, and what you are looking at is contamination. There is a lot more that could be said, and I will leave this to others.

I would not be too fussed about the degree of polish. Polish, per se, does not indicate how sharp a blade will get. It is where the blade is polished that counts. It may also be worth while considering a stone with finer grit (12000), not for polish but for smoothness/sharpness. And wash off the blade/guide between stones.

Regards from Perth

Derek

Re: Back Polishing Problem

#4

Re: Back Polishing Problem

Warren in Lancaster, PA

The number one consideration is not how the back looks or what forum members think about the S3 stone, but how the chisel performs for you. I borrowed an S3 stone from a friend twenty years ago; I recall it being adequate as a finishing stone. If you let the stone get a little toward dry and lighten up the pressure, it will give a finer scratch pattern. And if, in your hands, the S3 does a good job of polishing out to the very edge of the chisel after dulling from use, then it will perform better than a much finer stone that is not polishing all the way to the edge.

So give it a try in real work and get some base line experience. That way if you try out another finishing stone you will know what it is doing for you.

Re: Back Polishing Problem

#5

Re: Back Polishing Problem

wilbur

I don't worry too much about achieving a mirror finish. What's more important is the consistency of your scratch patterns. The fact that your scratch patterns instantly change when you switch direction with your 6000 grit waterstone tells me that you've gotten all the benefit from that stone that you can get. If there was a deeper scratch left over from your 1000 grit waterstone, it would still remain, or at least it wouldn't be "almost instantly replaced" by scratches going in another direction.

You often hear that a mirror finish is the goal when flattening the back of a chisel or plane blade. What we are doing is using a mirror finish as a surrogate for an even covering of the back with a scratch pattern that is only due to the last step in your sharpening process.

The problem is, what causes a mirror finish does not directly correlate with what causes a sharp edge. A sharp edge is achieved when you have very small scratches on the back and bevel side that intersect at the cutting edge. A mirror finish is achieved when you have a very even scratch pattern, without much variation in the size of the scratches.

If you can wrap your brain around this idea, it should become apparent that you can have an even pattern of relatively deep scratches that provide a mirror appearance, and an uneven pattern of shallower scratches that will look hazy.

It's easier to understand this if we put some numbers on this. I know that my 5000 grit waterstone will leave a mirror finish on a chisel back. What the manufacturer's information tells me is that this waterstone has abrasive particles that are about 4 microns in diameter, and when I look at the chisel with a magnifying glass, the scratch pattern is very even. What this tells me is that the particle size in this waterstone is very uniform.

If I followup with my 8000 grit waterstone, the back becomes hazy. This waterstone has particles that are about 1.5 microns in diameter. When I look at the back, the scratch pattern is definitely finer than the 5000 grit waterstone, but is not as even. My guess is that even though this waterstone has particles that are nominally 1.5 microns, the particles vary more in size around that 1.5 micron mark than the particles in the 5000 grit waterstone, which leads to a more uneven scratch pattern that is still finer than the previous step.

In use, the chisel feels sharper after finishing with the 8000 grit waterstone than if I stop with the 5000 grit waterstone, which is the real world evidence to support the idea that a mirror finish is not necessarily the best test for sharpness. I think Warren is right on when he says to use the chisel and see how it works.

Re: Back Polishing Problem

#6

Re: Back Polishing Problem

Paul Dzioba

Hi Tony,

I have a King finishing stone and I concur with Warren. Let the slurry get drier and drier as you finish up and you will get a better finish and sharper edge.

Regards,

Paul in NJ