New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Yankee tools box dates

Posts

Yankee tools box dates

#1

Moses Yoder

Yankee tools box dates

Moses Yoder

Our fair is coming up on Saturday and this year I think I will enter my Yankee 41 Y push drill in the "Hand Carpenter Tool" category. Normally I take first place in this category. It is like new (an I mean like brand new except for one tiny spot, maybe an original defect) in the original box with the paper wrapping. The catch is it has to be over 50 years old. I want to determine the age by dating the box. The problem is on this computer I no longer have the good Yankee Tools sites marked and I cannot find them on Google. If someone could help me find a good site where I can find out how old the box is I would greatly appreciate it.

Re: Yankee tools box dates

#2

Re: Yankee tools box dates *LINK*

Bob Entwisle in NJ

Hi Moses,

Not sure if this is any help or not.

Bob n NJ


http://www.wkfinetools.com/hUS-borTools/NorthBros/pubs/1926-YankeeTools/1926-YankeeTools-NorthBros.asp

Re: Yankee tools box dates

#3

Re: Yankee tools box dates

Wiley Horne--So. Calif.

Hi Moses and all,

I don't think there is a published type study of Yankee push drills. George Langford, at George's Basement, did quite a typography of Norh Bros. braces; though not drills, he may know something about their dates if you write him.

There are a number of clues to be found at Sandy Moss's website, especially at the North Bros. brace page:

http://www.sydnassloot.com/Brace/Northb.htm

Quotijng verbatim from that page:

"After the end of WWII changes took place at North Bros that ultimately resulted in some compromise of the quality of Yankee braces. In On April 18, 1946 the Stanley Tool Works acquired North Bros to establish their entry into the spiral ratchet screwdriver business, and upgrade their line of braces. After the takeover, the North Bros braces and other tools were first marked, "North Bros Mfg Co., Philadelphia, Division of Stanley Tool Works." These "Philadelphia –made" tools seem to have retained the construction quality for which North Bros was famous. In 1956 Stanley split off much of its former North Brothers holdings under the name, "Yankee Tools Inc." Braces and other products produced between 1956 and 1958 were marked with this name, and were still produced in Philadelphia. Gradually, however, the North Bros tooling was relocated to the Stanley home area of New Britain, Conn, and on June 30, 1958 the "Yankee Tools Inc" name was discarded.. From this time the "Yankee" line of tools is marked only "Stanley" (in a notched rectangle), and the North Bros name is dropped. The Yankee braces and other tools from post-1958 generally show the decrements in quality that are associated with modern mass production. In generally the tools are not finished as well, have rougher machining, and poorer quality handles."

Bear in mind, he is talking about braces here, but a number of the dates mentioned will apply to push drills as well. Sandy Moss is a pretty accessible guy, and will answer your email if you write him--he may know the answer to the question you have asked. He is also a very fair and knowledgeable dealer, and a good guy to buy from--I know from experience.

Wiley

Re: Yankee tools box dates

#4

Moses Yoder

Re: Yankee tools box dates

Moses Yoder

I took a closer look at it after reading more and it does have the Stanley label on it. I then had the bright idea to see if the box matched the Stanley box dating chart in Walter's book and it does. The box type was used from 1962 to 1980, and it does have the separate label so would probably be an earlier type. I am claiming it is 50 years old and seeing what the judge says. The judge is actually very knowledgable about tools as near as I can tell but I have figured out the condition of the tool means more than its uniqueness or rarity.